Determine the maximum safe service live load that the beam can carry if the service dead load is 10KN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPa and fy=415MPA. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70mm 300 mm 7.2m 6.7m A В O () O O

Determine the maximum safe service live load that the beam can carry if the service dead load is 10KN/m including the beam weight and based on the capacity of the beam section shown. Use fc'=40MPa and fy=415MPA. top bars are 6-36mm and bottom bars are 3-36mm, center to center distance between the top bar layers is 108mm. WLL = kN/m 70 mm 108 mm 352 mm 70mm 300 mm 7.2m 6.7m A В O () O O

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.5.8P

See similar textbooks

Similar questions

Determine the safe load of the column section shown, if it has a yield strength of 25 MPa. E = 200000 MPa. Use NSCP Specifications. Fyz248 mpa Properties of Channel Section d = 305 mm t₂ = 7.2 mm A = 3929 mm² t₁ = 12.7 mm Ix=53.7 x 10mm¹ x = 117 mm Properties of W 460 x 74 A = 9450 mm² b = 190 mm ly= 1.61 x 10 mm x = 17.7 mm tw = 9.0 mm rx = 188 mm ry = 41.9 mm d = 457 mm tr = 14.5 mm Ix = 333 x 10 mm Iy = 16.6 x 10mm* 7.21 When the height of column is 6 m. When the height of column is 10 m. Assume K= 1.0 457 CIVIL ENGINEERING- STEEL DESIGN
Determine the design moment capacity of the beam with given properties below. bf = 550mm bw 350mm tf = 100mm %3D d = 370mm %3D d' = 100mm %3D fc' = 34.5 MPa fy = 400 MPa %3D As = 6-32mm bars a USE NSCP 2001, Mu = kN-m b. USE NSCP 2015, Mu = kN-m
W3D 25 Y= 155 %31 1oow= 2500 KN 27=310mm X= 475 Z= 60 %3D 102=600mm
Q2:If allowable stresses are ot = 165MPa, oc=100MPa t = 70MPa determine max. value of W. W 150mm 50mm 2m 8m 2m 150mm
For the given properties of beam below. Design the reinforcements of the beam. d'=75 mm b=400 mm d=580 mm fc'=35 MPa fy=320 MPa Mu=1000000000N mm Input is 0 in As' if compression bars are not needed. A. USE NSCP 2001, As = mm2, As' = mm2 B. USE NSCP 2015, As = mm2, As' = mm2 %3D
Use AISC Equation E3-2 or E3-3 and determine the axial compressive strength oP for the following cases: a. L = 15 ft 233.1 kips 159 kips 26.65 kips O 259 kips L W10 x 33 A992 steel
For the given properties of beam below. Compute the flexural capacity of the beam. b = 390mm d = 440mm d' = 80mm fc' = 34.5MPA fy = 350MPA As = 4 - 40mm As' = 2 - 32mm A. USE NSCP 2001, Mu = kN-m B. USE NSCP 2015, Mu = kN-m
A built-up section shown, 30 feet long, is fixed at both ends and braced in the weak direction at the midheight. A992 steel is used. Determine the following: 11. Ix 12. Ky 13. effective slenderness ratio 14. Fe 15. LRFD design strength 16. ASD allowable strength 18 4 W10 × 49 A 14.4 in² bf 10 in d. 10 in tw 0.340 in tf 0.560 in Ix= 272 in¹ Iy=93 4in¹ W10×54 A 15-3 in² bf 10 in d = 10 lin tw0-370 in tf 0.615 in Ix= 303 in 4 Ty = 103 in 1
AW 12 x 65 column section shown in the figure is pinned at each end and has an additional support in the weak direction at a point 4.1 m from the top. Use X- 4.8 m K 1 for both directions. X+Y Properties of W 12 x 65 A 12323 mm2 - 134.11 mm ry 76.71 mm Fy- 248 MPa Determine the allowable compressive strength (kN).
Given: The T- beam cross section in Figure 3. Find: Calculate the following: a. The gross moment of inertia, Ig b. The location of the neutral axis of the cracked section and Icr. c. The effective moment of inertia, lê, assuming that Ma = 0.6M₁. (don't include the 2 # 4 bars in the top flange as compression steel when calculating M₁) f=5000 psi NWC fy = 60,000 psi Cc = 1.5 in #4 stirrups -b₁ = 50 in 20 in 10 in Figure 3-T-Beam cross section. 2 #4 2 # 10 6 in 18 in
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
4 - For the beam loading configuration and cross-section shown below, what is the maximum allowable load P given that the maximum allowable stress (in tension and compression) is 120 MPa? PO Р 1.6m PN ż 0.8m 0.8m P80 1.6m Р 30 30 T 10 dimensions in mm beam cross-section (same as problem 3, but inverted)