H.W A rigid Slab weighing 600 K bronze vads and one Steel Vocd Cach off 6000 mm2 area at a temPerature of 15 Ĉ as shown, find the tem Perature at which the Stress in steel Ved willbe zero ? take: Cuefficient of exransion for Steel = 12Mm/m.č Coefficient of exPansion for bronze = 18 Mm/m.č Young's modulus for steel = 200Gla Young's modulus for bronze = 80 Gla %3D 600 IW bronze 25crpm 30emm Steel

H.W A rigid Slab weighing 600 K bronze vads and one Steel Vocd Cach off 6000 mm2 area at a temPerature of 15 Ĉ as shown, find the tem Perature at which the Stress in steel Ved willbe zero ? take: Cuefficient of exransion for Steel = 12Mm/m.č Coefficient of exPansion for bronze = 18 Mm/m.č Young's modulus for steel = 200Gla Young's modulus for bronze = 80 Gla %3D 600 IW bronze 25crpm 30emm Steel

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q/ Find the Maximum stresses in Steel and Aluminum. Est= 210G pa and E al%3D 70 G pa ? W= 15 Kn.M 120mm 5m Al steel 60mm 140 mm
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C dy 40 kN -dr 30 kN
3. Find the thickness of a cast iron cylinder 250 mm in diameter to carry a pressure of 0.7 N/mm2. Take maximum tensile stress for cast iron as 14 MPa. [Ans. 6.25 mm]
2. The bronze bar 3 m long with a cross-sectional area of 350mm2 is placed between two rigid walls. At a temperature of -20 oC, there is a gap of 2.2 mm. Find the temperature atwhich the compressive stress in the bar will be 30 MPa ifthe bar will experience:a. No tensile.b. With an tensile of 5,000 N.Use α = 18.0 x 10-6 /oC and E = 80 GPa.
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
= 5.29 Knowing that P Q = 480 N, determine (a) the distance a for which the absolute value of the bending moment in the beam is as small as possible, (b) the corresponding maximum normal stress due to bending. (See hint of Prob. 5.27.) THEMOM DV P nedw to absol be500 mm 500 mm pripoly not Alase BOLERON 9T AO mersib anamorp sode bol ng appiled: the batuda Fig. P5.29 edi te ating out A Daniloobo CV. D (5.6b) Q f 12 mm s mas i nadw bozudiruaib ebimnice di Tibe sade 2b2 B (10. busd bus bris to pages. eda sdtlanbi are noe minnas li batalize yo led ditw i most u tamom gaiboedshus en betrovalmisoled loads Dignst Box brol 18 mm
2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 10 kN? Specify whether tension or compression. Bronze Aluminum Steel A =400 mm2 A= 600 mm2 A = 300 mm2 2P ЗР 4P P -3 m 5 m 4 m Stress in Bronze (MPa) %D Stress in Aluminum (MPa) %3D Stress in Steel (MPa)
dae 11.25 kips st steel ∙Alum in um A fully bonded aluminum Outer shell and Steel inner core bar is axially loaded. Find the ✓1.25 kips normal stress for the alum', num outer shell. Answer in ksi Given: EA = 11,000 ksi Al Est = 29,000 ks; XAL = 13.5 x 10-6 Y OF Xst = 6.5 x 10-6 1/F dAl = 1.0 in. dst = 0.25 in. AT = 65 °F
1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests. It has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑Y 40 MPa 80 MPa 25 MPa
O Compute the maximum value of P that will not exceed a stress of bronze of 100 MPa. Bronze A=450 mm2 A=600 mm Aluminum Steel A=300 mm 2 Compute the max. value of P that will not exceed a stress of E-83 GPa E=70 GPs E=200 GPa aluminum of 90 MPa. 600 mm 1,000 mm 800 mm 3Compute the maximum value of P that will not exceed a stress of steel (3) of 140 MPa.
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
10.1 x 10° psi), which consists of The aluminum rod ABC (E = two cylindrical portions AB and BC, is to be replaced with a cylin- drical steel rod DE (E = 29 X 10 psi) of the same overall length. Determine the minimum required diameter d of the steel rod if its vertical deformation is not to exceed the deformation of the aluminum rod under the same load and if the allowable stress in the steel rod is not to exceed 24 ksi. 28 kips 28 kips A D 12 in. +1.5 in. B -2.25 in. - 18 in. C E