1. Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. Cº) | L (m) | d (m) 0 (degree) E (GPa) P (kN) Steel 500 TI.2 190 3 35 Aluminium 400 18.9 70

1. Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. Cº) | L (m) | d (m) 0 (degree) E (GPa) P (kN) Steel 500 TI.2 190 3 35 Aluminium 400 18.9 70

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.4P: A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen with a diameter of 1 2 inch and a gage length (the length over which the elongation is measured) of 4 inches. The dam were plotted on a load-displacement graph. P vs. L. A best-fit line was drawn through the points, and the slope of the straight-line portion was calculated to be P/L =1392 kips/in. What is the modulus of elasticity?
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
3) An bronze rod is rigidly attached between a aluminum rod and a steel rod as shown. Axial loads are applied at the positions indicated. Find the maximum allowable value of P that will not exceed a stress in steel of 140MPA, in aluminum of 90MPA or in bronze of 100MPа. Aluminum A = 500mm? Bronze A = 200mm? Steel A = 150mm2 2P ЗР L st = 1.2m L br = 2m Lal = 3.5m
A hollow aluminum tube is rigidly attached between steel rod and a bronze rod as shown. Axial loads are applied at the positions indicated. Find the maximum value of P that will not exceed a stress in aluminum of 80 MPa, in steel of 150 MPa or bronze of 100 MPa. Steel Aluminum Bronze А P> ЗР - 2P outside = 30 mm d inside = 20 mm d d = 16 mm d = 60 mm -100mm- -150mm- -125mm-
A compound bar is subjected to a compressive force of P=556 kN by means of a rigid endplate at the top. If the length of the bar is 876mm, determine the stress in the alurninum core. Answer in MPa. Round off your final answer to 2 decimal places. 25 mm Brass core E = 105 GPa a = 20.9 x 10-6/°C Aluminum shell E = 70 GPa Q = 23.6 x 10-6/°C 60 mm
1.(e) The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests. It has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑Y 40 MPa 80 MPa 25 MPa
The state of plane stress shown occurs at a critical point of a steel machine component. As a result of several tensile tests, it has been found that the tensile yield strength is o, = 250 MPa for the grade of steel used. Determine the factor of safety with respect to yield using (a) the maximum shearing stress criterion, and (b) the maximum distortion energy criterion. ↑y 40 40 MPa 80 MPa 25 MPa ➜X
An aluminum rod is rigidly attached between a steel rod and a bronze as shown. Axial loads are applied at the positions indicated. Find the stress of each rod in MPa. Steel Aluminum Bronze A- 500mm? A = 400mm? A - 200mm 40KN 10KN 20KN 2.5m 2.0m 1.5m
Q # 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure. Axial loads are applied at the positions indicated. The value of P is limited to 20 KN in bronze, 72 KN in aluminum and 28 KN in steel Find the area of each section that will not exceed a stress in steel of 280 MPa, in aluminum of 180 MPa, or in bronze of 200 MPa. CLO -2 Steel Aluminum Bronze 2P 4P 2.5 2.0 1.5
Problem 1.5-2 A bar of length 2.0 m is made of a structural stoel having the stres-strain dingram shown in the figure. The yield stresa of the steel is 250 MPa and the slope of the initial lincar part of the stress-strain curve (modulus of elasticity) is 200 GP. The bar is loaded axially until it eklongates 6.5 mm, and then the load is removod. How does the final length of the bar compare with its orig- inal length? Hint: Ue the concepts illustrated in Fig. 1-36h) MP 300 200 100 0.002 0.004 0.006
A high strength steel with modulus of elasticity of A N/mm', yield strength of B N/mm and crushing strength of C N/mm2 is used for a test. In the instance of crushing total strain was measured as D a) Find the ductility of steel. b) What should be the diameter of the bar to carry a load of E kN without any plastic deformation. A B D E 249000 1420 1660 2.90% 59
_Find: (a) the stress in the Steel and Ahuminium rods after the loap P applied and the temprature raised 60 C" and (b) the displacement under the load P. Using the data in the Table below. Rod A (mm) a (um/m. C°) L (m) d (m) 0 (degree) E (GPa) P (kN) Steel 400 T1.2 195 3 35 Aluminium 300 18.9 4 30 90 Aluminium Steal 4m 2m