On separate graphs, sketch the heat flux and temperature as a function of position (fromthe air to the subsoil), with and without mulch. Make sure that your sketches reflect thatthe system is at steady-state and account for the relative magnitudes of the thermaland heat transfer coefficient. You don't need to calculate anyfor these graphs.17conductivitiestemperatures - Ground cherry seeds need to be planted at a depth of 1-cm below the surface and will onlygerminate if their surrounding soil is at a temperature of 24-30°C. Farmer Joe wants to knowwhether adding straw mulch (Amulch = 0.05 W/m K, Lmulch = 10 cm) on top of his soil willincrease the odds of germination.The topsoil in Delewareis sandy loam (soil = 0.5 W/m K), with a thickness of 1 m.Immediately beneath the topsoil is the subsoil, which is at a constant temperature of Tsubsoil =10°C. You can assume that the air in Delewareis fairly calm, with a heat transfer coefficientof h= 10 W/m².K.deleware(a) Sketch the system (with and without mulch), labeling all temperatures, dimensions, andproportionality constants. You may assume that the subsoil, topsoil, mulch, and air are atsteady state. You should have two sketches.

Answered: Image /qna-images/answer/3064a601-9f8f-4bfa-80fc-7f5abdeff47b.jpg

Ground cherry seeds need to be planted at a depth of 1-cm below the surface and will only germinate if their surrounding soil is at a temperature of 24-30°C. Farmer Joe wants to know whether adding straw mulch (mulch = 0.05 W/m K, Lmulch = 10 cm) on top of his soil will increase the odds of germination. The topsoil in Deleware is sandy loam (2soil = 0.5 W/m-K), with a thickness of 1 m. Immediately beneath the topsoil is the subsoil, which is at a constant temperature of Tsubsoil = 10°C. You can assume that the air in Deleware is fairly calm, with a heat transfer coefficient of h = 10 W/m².K. deleware (a) Sketch the system (with and without mulch), labeling all temperatures, dimensions, and proportionality constants. You may assume that the subsoil, topsoil, mulch, and air are at steady state. You should have two sketches.

Ground cherry seeds need to be planted at a depth of 1-cm below the surface and will only germinate if their surrounding soil is at a temperature of 24-30°C. Farmer Joe wants to know whether adding straw mulch (mulch = 0.05 W/m K, Lmulch = 10 cm) on top of his soil will increase the odds of germination. The topsoil in Deleware is sandy loam (2soil = 0.5 W/m-K), with a thickness of 1 m. Immediately beneath the topsoil is the subsoil, which is at a constant temperature of Tsubsoil = 10°C. You can assume that the air in Deleware is fairly calm, with a heat transfer coefficient of h = 10 W/m².K. deleware (a) Sketch the system (with and without mulch), labeling all temperatures, dimensions, and proportionality constants. You may assume that the subsoil, topsoil, mulch, and air are at steady state. You should have two sketches.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.3DP

See similar textbooks

Similar questions

A camera used for monitoring marine life is placed in water where T.. -5°C and the convection heat transfer coefficient h=1420 W/m²K. The camera is operating, but its battery is experiencing thermal runaway, causing the camera to become very hot, and there is volumetric heat generation, qe inside it. There is no heat generation within the waterproof, protective enclosure surrounding it. 00:08 The camera is already compromised; however, its owner hopes to save the protective case. Each interface (between layers A and B and between layers B and C) must not exceed a temperature of 185°C, or these plastic, protective layers will begin to melt. Approximate the camera and its casing as a composite, rectangular object with flat surfaces. The device's total thickness, L=LA + 2LB +Lc, is much smaller than its area (into the page); therefore, 1-D conduction can be approximated through the layers. On the left surface of layer A, the temperature is measured to be T₁ = 8.0°C, and the temperature on…
Required info: There is a 2.00 cm thick stagnant air pocket. a) What thickness of cork would have the same R-factor as the stagnant air pocket? The thermal conductivity of air is 0.0230 W/m-K and of cork is 0.0460 W/m-K. b) What thickness of tin would be required for the same R-factor as a 2.00-cm-thick stagnant air pocket? The thermal conductivity of air is 0.0230 W/m:K and of tin is 66.8 W/m-K. THANK U
H.W: 10-02-2021: The exterior wall of a building consists of 100 mm thick face brick (k = 0.9 Wm¯'K'), 40 mm thick polystyrene insulating board (k 0.036 Wm'K¯), 125 mm thick concrete block (k = 1.8 Wm¯'K') and 15 mm thick interior gypsum board (k = 0.18 Wm K). The inside and outside convective heat transfer coefficients are 6.5 Wm K and 22.5 Wm K respectively. The outside air temperature is -5°C and the inside air temperature is 20°C. The wall is 3 m high and 15 m long. Calculate (i) the rate of heat loss through the wall,
Design and study of floating Roofs for Oil storage tanks.Case study :*100 mm of rain above the roof. what the Challenges and Solutions of this case study ?
A 2.5-m-tall steel cylinder has a cross-sectional area of 1.5 m2. At the bottom, with a height of 0.5 m, is liquid water, on top of which is a 1-m high layer of gasoline, relative density of 0.8. The gasoline surface is exposed to atmospheric air at 101 kPa. What is the gage pressure at the liquid interface? what is the answer? a.0.077 atm b.15.839 psi c. 1.139 mmHg d.108.848 kPa
To ensure a tight fit, the aluminum rivet used in airplane construction are made slightly larger than the rivet holes and cooled by dry ice (solid CO2) before being driven. If the diameter of a hole is 0.500 cm, what should be the diameter of a rive at 20 degree Celsius if its diameter is equal that of a hole when the rivet is cooled to -78 degree Celsius, the temperature of dry ice? Assume the coefficient of expansion to remain constant. (Given and solutions)
O heat \-140°C source Civen: composite wall (3 layers) Pory unethane board corere te rock (15 cm, wool k>0.762 (0.5 cm , (0.38cm, WIm2 K k= 0.0397 w [m" K Tconue te 0.03 92 m²K 32°C Cxposed to air and heat soure Emirr ivity %3D -0.90 Sowe: 1. given conyeetiye heat trans fer 8,23 (w /m k), coeficint oo nside air %3D diefermine temperature in side aiv at end of com posite wall heard transfer 2. Sue thermal radiation to (negleck natual Convection) 3. using heat transfer from # 2, in SONE mtergace temperature, temperant ure innermost wall
1. A 4-m high and 6-m-wide wall consists of long 15-cm x 20 cm cross section horizontal bricks (k of 0.69 W/m K) separated by 2-cm thick plaster layers (k of 0.2 W/m K). There are also 2-cm-thck plaster layers on each side of the brick and a 3-cm-thick rigid foam (k of 0.025 W/m K) on the inner side of the wall. See figure below. The indoor and the outdoor air temperatures are 18 and -8°C, respectively. Convective heat transfer coefficient for inside and outer surfaces are 8 and 22 W/m² K, respectively. Assume 1-D heat transfer. Neglect radiation. Foam inside a. assume any plane wall normal to the x-direction is isothermal, draw the thermal circuit and calculate the heat transfer rate through the wall b. c. assume any plane parallel to the x-axis is adiabatic,, draw the thermal circuit and calculate the heat transfer rate through the wall Compare the results from a and b, discuss the reason for any difference there might be. brick brick brick L15 cm. X plaster 1 cm 20 cm 1 cm outside
Refer to the figures shown below depicting an isothermal process. (a) Prove that the shaded area on the P-Vplane of Figure 1 & 2 are equal. (b) Determine the slope and concavity of the curve.
2-D: A fin may be manufactured as an integral part of a surface by using a casting or extrusion process, or it may be separately brazed or adhered to the surface. From thermal considerations, which option is preferred? 2-E: What is the difference between steady-state and transient heat transfer processes? Give an example for each of them. 2-F: What is the physical interpretation of the Biot number? 2-G: For flow over a flat plate, sketch variation of local convective heat transfer coefficient, h(x), versus the distance along the plate x for laminar, transition, and turbulent flow regimes.
Let's say a 3.0 gram copper wafer is dropped from a height of 50.0 meters. If 60% of the potential energy lost in the drop could be converted to thermal energy used to heat the copper from an initial temperature of 25 degrees celsius, what would the final temperature of the copper wafer? Would the answer be different if the wafer has a mass greater than 3 grams? Note: the specific heat of copper is 387 J/(kg*K). The temperature is between 25.8 and 26.0 degrees celsius, yes the bigger the mass the greater the energy. O The temperature is between 25.6 and 25.8 celsius, answer does not depend on mass. O The temperature is between 25.0 and 25.2 celsius, answer does not depend on mass. O The temperature is 25.5 and of course the more mass something has the greater energy will be needed to raise the temperature. The temperature is 26.2 and if the mass is doubled so will be the change in temperature. O The temperature is 25.9 degrees celsius and the answer does not depend on mass. O The…
What is the thermal resistance of a 3 in fired clay brick with density of 120 Ibm/ft3 a. 0.422 b. 6.8 c. 0.48 d. 6.2