Given the following cross-section notes for a road grading work: x1 3.5 x2 -3.2 1.2 1.2 2.8 The road bed is 9 m wide and the slide slope for cut is 1:1 and for fill is 1.5:1. Determine the area of cut of the section.

Q: Define Dynamic viscosity.

A: DYNAMIC VISCOSITY:   Dynamic viscosity is the properly of fluid to resist the flow. Or to be more…

Q: relative consistency with its formula.

A: Consistency The quality of always behaving or performing in a similar way, or of always happening in…

Q: C. Put the following words related to roads, bridges and waterways (barrage, pavement, dam, curb,…

A: Roads i) Pavements ii) Curb iii) Pedestrian crossing   Bridge  i) Aqueduct  ii) Deck iii) Barrage…

Q: With the measurements in the following table, calculate the soil moisture flux q (cm/day) between…

A:

Q: So there's 3 forces on a body and they're not parallel and they intersect at a point so their angles…

A:

Q: Explain the principle of 5S in Construction. Complete the answer please.

A: Introduction- Construction- It refers to the methods and business associated with assembling and…

Q: Q6: Construct a graphical scale from the given Statement of Scale is 1 inch representing 1 mile and…

A: Draw a straight line of 6 inches and divide it into 6 equal parts and assign a value of 1 mile each…

Q: y 130 mm 30 mm 30 mm -40 mm 40 mm-

A:

Q: Q1: Discuss in detail Kennedy and Lacey Theory? Write down all the design steps. Civil Engineering…

A:

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Define coefficient of volumetric expansion.

A: The coefficient of volumetric expansion is defined as the ratio change in volume with respect to the…

Q: What is the general range of L/G ratios?

A: L/G ratio stand for the liquid to gas ratio. which is the ratio of the waste slurry to the flue gas…

Q: The solution came out all in one line. Making it difficult to understand. Please Can it be written…

A:

Q: What is the volume of this room in cubic feet?

A: Knowing the volume of a room is important when determining its heating and air conditioning needs.…

Q: Q2. Draw a diagonal scale to show kilometers, hectometers & decameters when 1 km is represented as 2…

A: where we can read up to 3 dimensions. then the scale used diagonal scale in this scale we used the…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 225 pounds + 598.17 pounds + 1.982 pounds

A: Pound: It is a unit of mass or weight of a body. It is abbreviated as lb which is an ancient Roman…

Q: How did you derive the formula?

A: Given: h1= 200 mm   h2 =80 mm   k1=0.004 cm/sec,   H1 = 100 mm   H2 = 150 mm. Required: To explain…

Q: Write the formula for the effective length factor?

A: The effective length factors of columns  plays major role in the design of compression members.…

Q: can you please explain your calculations? Im not sure on how you got 2 for the first part

A: Given: The velocity distribution in the boundary layer is given by the expression: uU=1-exp-2×yδ The…

Q: X 0.75 3 -3.5 1.5 1.5

A:

Q: 0 mm 20 mm x= ky? 30 mm etermine: enter of Area in x direction, overline x 1U-Sclect) mm enter of…

A: To find centroid

Q: 2. A grad of 1.5% intersects a grade of -2.5% at station 1+080 of elevation 68.94m. If the summit is…

A: Solution-The given values are as follows  The grade g1=1.5%The grade g2=-2.5%Station…

Q: Describe the Particle Shapes and Sizes.

A: Particle size refers to the dimensions of particles (solid, liquid and gaseous. It is used for…

Q: How to calculate error % in viscosity?

A: Sources of error in capillary viscometer 1. Angular misalignment of the viscometer off the vertical…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: our own word three sentences of the field hydrology.

A: The detailed study of rain ,snow and other precipitation forms and the movement of water through…

Q: H MM 0 10 20 30 40 50 60 70 80 90 100 DIMENSION THE PART USING METRIC DIMENSIONS. USE DIVIDERS OR…

A: The front view and top view of an object is shown in the above figures. Also scale of dimensions…

Q: Draw the full sectional front view, as well as draw the top view and side view of the object as…

A: The Section A-A Front View diagram of the given object is as shown below (not to scale):

Q: F = 500 lb 25° 45° 30 F2 = 750 lb

A:

Q: Classify the structure shown in the figure. OA. Indeterminate. 21st degree O B. Indeterminate, 24th…

A:

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: Give examples of primatic cylinder

A: It is also called a self-priming cylinder is a type of indirect hot water cylinder in which the…

Q: Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide.  The floor plan of Isobel and…

A: Scale can be defined as the ratio of the dimension in plan or map to the actual dimension  Scale is…

Q: Part A What is the ratio scale for the equivalent scale of 1 in. = 80 ft? Express your answer using…

A: 1 ft =12 inch given 80 ft =12*80=960in Ratio scale=112×80=1:960

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: 30 10 30 10 15 20 15 10

A: Line command of autocad is used  We can use either absolute coordinate method or relative coordinate…

Q: Determine external indeterminacy

A: Given data : Number of external support reaction (R)=2+1+1+2=6

Q: Convert 0.0351 to engineering notation. O a) 35.1 × 103 O b) 3.51 × 10–2 )c) 3.51 x 10² O d) 35.1 ×…

A: Solution:- We have to convert the given number into the engineering notation, The given number is…

Q: Draw the figure to an enlarged scale in Isohyetal method

A: The iisohyetal approach is a technique for calculating the average amount of precipitation within a…

Q: Draw the Orthographic Projections (Top View, Front View, Side View) For the Shapes Shown Below,…

A: Draw the top view ;