Convert 24 inches to feet.

Q: How many Type of Interior materils.

A: Interior materials : Interior materials are the materials which are used inside the house, like…

Q: Define Dynamic viscosity.

A: DYNAMIC VISCOSITY:   Dynamic viscosity is the properly of fluid to resist the flow. Or to be more…

Q: What is the relationship between sensitivity and radius?

A: The change in angle or gradient of the level that results in movement of the bubble is known as…

Q: What is the other name for air/cloth ratio?

A: The air to cloth ratio is defined as the total amount of air that is flowing through the filter of…

Q: How to find yarn count from it weight and how to find weight from it count ??

A: The yarn count, a number that indicates how fine or coarse a yarn is, determines the quality of a…

Q: 3. A cube, 7feet on each edge, is floating in a pool of fresh water. If 2feet of the cube is above…

A: Given data: Volume of cube=7×7×7 ft3 2 ft of cube is above the water surface.

Q: an 80 feet flagpole upper and lower diameter of 4 and 16 inches. find the cost of painting if at 10…

A: Given: The height of the flagpole is 80 ft. The upper diameter is 4 in. The lower diameter is 16 in.…

Q: A Totalstation encompasses: Spirit Level Theodolite EDM

A: Total station encompasses?

Q: Consider a glass with ice cubes. Sketch its plan, two elevations and a 3D image.

A: Glass with ice cubes- When a glass is filled with ice cubes, it can have many drawing shapes. All…

Q: What is the purpose of Recarbonation?

A: The process of adding carbon dioxide to lime-softened, clarified water in order to lower the pH and…

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: What is layerd cake

A: Layered cake:

Q: ETERMINE THE LOCATION OF CENTROIDAL X AND Y. NOTE: UNITS ARE IN INCHES.

A:

Q: lo" A 992 steel 14" -2" what is Mp= ? 14"

A: From the given data calculate all areas find the y bar find the Ix

Q: Define the size of a concrete cube?

A: Cube test of concrete is one of the most important tests done on concrete. It is also known as a…

Q: Q25. Draw the plan, section and elevation of the given line diagram. BАTH 2000 x 2500 BED 5000 x…

A:

Q: ooking at the X direction, provide the front view, top view, and left-side view using the meter…

A: The isometric Front, and side. Top view of above drawing is given below:

Q: How does carburizing work?

A: Introduction- Carburization- A low carbon steel is converted into a high carbon steel by the process…

Q: What is Sloped Glazed.

A: Glazing: The installation of glass to the building components or interiors of the structure is…

Q: DIFFERENT ACCESSORIES IN THE SHAPER MACHINE WORKS VERTICAL AND HORIZONTA

A:

Q: Differentiate between elasticity and plasticity.

A: Elasticity:  Elasticity is the property of a material which regains it's original shape once the…

Q: installed in the front lawn and along one side and seeded the remain- der with 3.5 pounds per 1,000…

A:

Q: How

A: 1 and 1 actually is the ratio representation of slope.

Q: What are the many kinds of bulbs used in the construction of buildings? Additionally, draw and…

A: It might be scary to walk into an electrical store. All of the lights are turned on at first…

Q: Describe a good rule of thumb for relating inches and centimeters?

A: For converting inches to centimeters, always remember inch is always bigger than centimeters.

Q: Isobel and Neliwe’s garage floor is 5400 mm long and 3000 mm wide.  The floor plan of Isobel and…

A: Scale can be defined as the ratio of the dimension in plan or map to the actual dimension  Scale is…

Q: What is  negative skin friction ?

A: Friction is the resistance to motion of one object moving relative to another. It is not a…

Q: lap splicing

A: A lap splice is when two pieces of rebar overlap to form a continuous reinforcement. This helps…

Q: Describe the term compressibility.

A: Compressibility:- It is defined as the capability of the soil to decrease its volume under…

Q: Figure 20-7 Questions 1-10. 44 8. 6 38 20 24 34 Ol 76 8 80 84 88 92 10 Match the dimensions…

A:

Q: Calculate the second moment of area for a 50 mm ×100 mm stud with the actual dimensions shown on…

A: Given:- The dimension of the stud = 50 mm × 100 mm  The actual dimension of the stud = 45 mm × 105…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.