Below in Figure is an isometric drawing of a component. Draw in First Angle Projection the following: draw front view of A-A, side view, horizontal view و طعوت $4

Q: Sketch thefollowing figure ,orthographic view ( using catia )  Metion the top view side view and…

A: From figure.......

Q: For the following figure, when * drawing the projection pointer in the direction of the arrow, it…

A: The imaginary flat plane on which image of any object is projected is known as plane of projection.…

Q: 4" 8" 6"

A: Solution:- Centroid of the given section: Table for calculation  Area inch2 x- coordinate inch y-…

Q: Object 3. a. Replicate the front, left and top side views given using the 1st angle projection. Add…

A:

Q: Draw in full scale front view ( indicated by the arrow F), top view and left-side view of the…

A: to find top , front and left view

Q: It is a pictorial representation that combines height-width-depth/length into a single view with30…

A:

Q: Use Scale ( 1:1), for the front and side views shown draw the isometric projection 50 30 25 40 80 30…

A: the isometric projection of the above front view and side view is

Q: For the following orthographic projection, presented in Third Angle projection: • Draw an isometric…

A:

Q: 38 13 Ф25 12 L 16 16 16 Ф25 56 76 Ф 50 64 7.28 i ,16 25 75

A: Answer :- 1. Top view of section:

Q: For the following figure provided, draw three orthographic views according to 3rd angle projection.

A: Front View:

Q: 1. Which tools is to enlarge or reduce size of object? 2. Which tool is used to extend an object to…

A: Ans  1.Users can enlarge view by using scale command in AutoCAD. Users may enlarge & reduce the…

Q: Show me this drawing Step by step how to draw it. thank you 25 1209 105° 30 Ø16 60° 40 60 70 it's…

A: To Determine Steps to be followed to draw the given drawing in CADD software.

Q: Find the vertical and horizontal line detect segmentation

A: Detecting vertical and horizontal lines in an image is a common task in image processing and…

Q: Show Isometric View.

A: Answer  We can obtain the isometric view from given views in Autocad using the following steps 1)…

Q: What type of drawing is shown (the bottom center of the object closest to the viewer comes to a…

A: A) 3 View incorrect. -> 3 view or orthogonal views are the projections when seen from a fixed…

Q: 120 22 56 34 44 RS O-2 Holes Top view Isometric view 36 64 40 26

A: Answer:- A- A Section and top view:

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L L FRP PRP 1. Discuss how…

A:

Q: Draw the orthographic side view of the given image with proper dimensions

A: Top view and front view is given, we need to draw side view

Q: Civil Engineering Orthographic and isometric projections are two basic types of graphic projection…

A: The statement Orthographic and isometric projections are two basic types of graphic projection is…

Q: Q.3. Use Scale (1:1), for the front and side views shown draw the isometric projection: 50 30 R30 30…

A: To get the isometric projection from the given views. 1. Draw two lines perpendicular to each other…

Q: Given the isometric view of the cut block objects shown, use rectangular grid paper to sketch a…

A:

Q: Looking at the x direction, provide the front view, top view, and left-side view using the meter…

A: Instructions :  To draw orthographic projections using third angle projection method, take the view…

Q: Draw the isometric view. The first photo is the given. The second one is given dimensions T 1st…

A: Solution-To Determine.To draw the isometric view from given orthographic projections

Q: Draw the multiview projection of the given isometric figure. L HRP FRP L 1. Discuss how did you draw…

A:

Q: Draw the half sectional front and side view, as well as draw the top view of the object as shown in…

A: The half sectional front view, side view and top view of the object is provided.

Q: Instructions: Draw the three basic orthographic projections of the figure. (Top View, Front View,…

A: Hand made drawing are attached herewith of different views. Which will give you idea about different…

Q: Using multiview, the user can layout drawings in different paper sizes at the same time. O True…

A: A multi-view drawing is one that shows two or more two-dimensional views of a  three-dimensional…

Q: If you obtained a drawing that contained Auto CAD polylines representing contours, what is the best…

A: Contour lines : A contour line for a two-variable function is a curve that connects locations of…

Q: Q3: Draw the Full Sectional Front view and Top View of given object 70 50 10 45 430 70 15 10 88 40

A: The following figure shows the Full Sectional Front View of the object.

Q: draw an isometric view of HEXAGONAL PRISM  where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: Exercise 1.6: Estimate the dimensions. Draw the Front view, Top view and Right view. Draw the…

A: Question related to the engineering drawingsmodel is given  FINDFront viewtop viewright…

Q: Given the following isometric drawing, how many edges are drawn as points in the right side view of…

A: ASKED: To determine the number of edges of the given isometric drawing that are drawn as points in…

Q: 150 25 40 185 25 75 50

A: To draw the front, top and side view of the given object. Given 3d object:

Q: O 16 O 30 12 24

A: Answer:- Section on AA

Q: 5. In editing dimension lines, why is it important that the offset of origin must be edited…

A: The dimension line is a fine, dark, solid line with arrowheads on each end. It indicates direction…

Q: Draw the right side elevation of the object with the given top and front elevations below ho.00…

A:

Q: Select all projections that have one principal plane on the object parallel to the plane of…

A: Answers are b, c and d One-point perspective Projection plane is parallel to two principal axes…

Q: 38 $25 نقيات 12¢ 16 16 16 $25 76 Ф 50 64 تمرين 7.28 75 16 قا

A: Answer:- 1. Top view of given shape: