Given the equations of motion {x(t)} and mode shapes {u},and {u}2 where:10.00 0.0069.00 -44.00|{x(t}}+{x(t)}=0,0.00 6.00-44.00 44.000.80and {u}2=-0.75{u}1.Which of the following initial conditions excite the first mode of motion only.0.80%3D1.001.17{x,} =1.000.70{x,} =1.450.800.70

Given: To find: Initial conditions that excite first mode only

Given the equations of motion {x(t)} and mode shapes {u}, and {u}2 where: 10.00 0.00 69.00 -44.00 0.00 6.00 {x(t)}+ {x(t)}=0, -44.00 44.00 0.80 and {u}2 1 -0.75 {u}1 Which of the following initial conditions excite the first mode of motion only. 0.80 {x} = {x,} = 1.00 1.17 {x,} = x) = 1.00 0.70 {x}= 1.45 0.80 {x} = 0.70

Given the equations of motion {x(t)} and mode shapes {u}, and {u}2 where: 10.00 0.00 69.00 -44.00 0.00 6.00 {x(t)}+ {x(t)}=0, -44.00 44.00 0.80 and {u}2 1 -0.75 {u}1 Which of the following initial conditions excite the first mode of motion only. 0.80 {x} = {x,} = 1.00 1.17 {x,} = x) = 1.00 0.70 {x}= 1.45 0.80 {x} = 0.70

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

All values equal to 1
Derive the equations of motion of the system shown below. You should describe the equations of motion in terms of the matrix form. X1 m k 5m 2k 2k m k 0000
C 14:40 Two cables AB and AC are acting on the pole with forces FAB 760N and FAC = 480N with parameters defining the attachment points shown in the table. We want to write the vector FAB in cartesian vector form. X - X2 Y₂ FAB FAC X1 Y1 X2 Y2 = Y₁ IN parameters value units FAB 760 N FAC 480 L 8 3 wamap.org 33 A 3 4 Z F₁ AB î+ B N Ζεεειειε m m m Write the vector FAB in Cartensian Vector Notation. Round your final answers to 3 significant figures. m L X1 3+
J 5: !!!Please show it mathematically, not theory
A projectile is launched with a velocity of 100 m/s at an angle of 30° above the horizontal. Create a Simulink model to solve the projectile's equations of motion, where x and y are the horizontal and vertical displacements of the projectile. X=0 x(0) = 100 cos 30º x(0)=0 ÿ=-g y(0)=0 y(0)=100 sin 30º Use the model to plot the projectile's trajectory y versus x for 0≤t≤10 s.
To create AutoCAD Q: Use the principle of the geometric model shown in the following figure? R8 16 22 50 015 50 425 40 80 20 r
mechanical vibrations
For the mechanism shown below;i) Show variables on the figure,ii) Determine the space scale, ks=?iii) Write vector loop closure equation(s) by using complex numbers,iv) Solve the vector loop equation in order to determine the relative position ofpiston at point D with respect to point B when 2=60o.
Use t'=20.4 instead of 8.4 and use the formulas attached
I’m am struggling with this question
1. For the linkage system show, Link 1 moves along the vertical direction via a linear motor. Link 2 and 3,,dependent on the motion of Link 1, will move accordingly. Perform position analysis using Chace Mehod: Draw the loop closure vectors for the problem. (a) (b) Determine the unknowns. (c) Determine which kinematic case it is (d) Determine equations for the unknowns as function of known variables. (e) Assume link 1 is located 3 inches above the x-y coordinates, and link 2 has a length of 5 inches. Determine the numerical values of the two unknowns for this specific configuration. Link 1 X Link 2 Link 3
answer completely please