Given: Point A on rod AB has an acceleration of 5 m/s² and a velocity of 6 m/s at the instant shown. Upon using the IC, the angular velocity w of the rod is calculated and equals to 1 rad/s CCW. The angular acceleration a of the rod at this instant is Applying the relative acceleration equation aв = a₁ + ax FBA-00²TB/A agi=-5j+akx (3 i-4j)-w²(3 i-4j)

Given: Point A on rod AB has an acceleration of 5 m/s² and a velocity of 6 m/s at the instant shown. Upon using the IC, the angular velocity w of the rod is calculated and equals to 1 rad/s CCW. The angular acceleration a of the rod at this instant is Applying the relative acceleration equation aв = a₁ + ax FBA-00²TB/A agi=-5j+akx (3 i-4j)-w²(3 i-4j)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The wheel in the figure rotates clockwise with a constant angular velocity of 120 rpm. The pin Dis fixed to the wheel at a point 125 mm from its center and slides along the guide in the arm AB. Determine: (a) The angular velocity AB (rad/s). b) The angular acceleration AB of the arm at the instant shown (rad/s2). 60 120 грm 375 mm
-S R For the slider-crank mechanism shown, let R = 1.9 in., L = 6.1 in., and H= 1.2 in. Assuming that WAB= 4850 rpm and is constant, determine the acceleration of point D at the instant when = 10°. (Round the final answer to the nearest whole number. Include a minus sign if necessary.) B AWAB αAB L H Ĵ View previous attempt The acceleration of point D is ap ft/s² for ₁ = 56.12°. The acceleration of point Dis ap ft/s² for 82 = 360° - 0₁. = = Check my work -86.250 î+ 3)
Q1: The crank OA of the offset sli der-crank mech ani sm rotates with a constant clockwise angul ar velocity w, = 12 rad/s. For the positi on shown: 1.1 The angular acceleration of link AB and the acceleration of B. 1.2 Locate the instantane ous center of zero velocity (IC) for the link AB. 60° 45° B OA = 75 mm AB = 225 mm 15° %3D
For the position shown where @ =53°, point 4 on the sliding collar has a constant velocity of v-1.25 m/s in the direction shown. At this instant BD is horizontal and DE is vertical. a) Find the velocity of point D and angular velocity of link DE by using instantaneous center of zero velocity, b) Find the angular acceleration of link BD and DE. 00 mm 10H 1Pomm
Question: At The Instant QA = 5 Rad/S, Pulley A Is Given A Constant Angular Acceleration A = 6 Rad/S... At the instant wA = 5 rad/s, pulley A is given a %3D constant angular acceleration a = 6 rad/s?. Determine the magnitude of acceleration of point B on pulley C when A rotates 2 revolutions. Pulley C has an inner hub which is fixed to its outer one and turns with it. WA A 50 mm 40 mm B 60 mm
Q1: The crank OA of the offset sli der-crank mech anism rotates with a constant clockwise angul ar velocity o, = 12 rad/s. For the position shown: 1.1 The angular acceleration of link AB and the acceleration of B. 1.2 Locate the instantane ous center of zero velocity (IC) for the link AB. 60° 45° B OA = 75 mm %3D 15° AB = 225 mm
ASAP
1. The center O of the disk has the velocity and acceleration as shown in the figure. If the disk rolls without slipping on the horizontal surface, determine the velocity and acceleration of point B at the instant shown. Point A is not assigned for this problem, but if asked, could you find its velocity and acceleration, too? 5 m/s² A 45° 0 B 0.2 m 0.2 m' 3 m/s y
Q1. Use the graphical method only, find the velocity of the piston for the system shown below and the angular velocity of the link AB about point A. The crank OA rotates counter clockwise at 3000 rev/min. If the angular acceleration of the crankshaft OA is 1200 rad/s, determine the angular acceleration of the connecting rod AB. Assume that OA = 150mm, AB = 250mm, angle BOA = 60°, ABO = 25°. G
The system shown moves so that the acceleration of point B in the position shown is ag = -5i {m/s²}. Also, the angular velocity of bar BC is known to be 5 rad/s clockwise. Find the acceleration of the slider block C. (Note that the next question is related to this one.) y WAB WBC 1 m Taylor T e а. ac = -25.42i {m/s²} b. ac = 41.07i {m/s²} 1 m A 30° a. ac = -25.42i {m/s?} b. ac = 41.07i {m/s?} C. ac = -15.65i {m/s²} d. Te a ac = -45.73j {m/s?} е. ac = -33.87i {m/s²}
Determine the angular acceleration of AB and the linear acceleration of A for the position = 90° if 8 = 4 rad/s and = 0 at that position. Use vector expressions to solve this problem. 400 mm 500 mm 400 mm OB
Bar OC rotates with a clockwise angular velocity woc = 2.9 rad/s and a counterclockwise angular acceleration đoc = 1.5 rad/s². The bar OC is a slotted member which accommodates the pin A attached to the sector. Determine the angular velocity w and the angular acceleration a of the sector. The angular velocity and the angular acceleration are positive if counterclockwise, negative if clockwise. Assume OA = 415 mm, d = 320 mm, e = 37°. A B d aoc Answers: rad/s W = 4.71 i -34.6 rad/s?