3. An 8 ft diameter cylinder weights 500 lb and rests on the bottom of a tank that is 3 ft long. Water and oil (SG=0.75) are poured into the left and right hand portions of the tank to the depths of 2 ft and 4 ft respectively. Assume that water has a specific weight of 62.4 lb/ft³. a) Compute the magnitude of the horizontal forces pushing on the tank. What is the net force? 2 3.464 -D sp g C b) Compute the magnitude of the net vertical forces pushing on each side of the tank.

3. An 8 ft diameter cylinder weights 500 lb and rests on the bottom of a tank that is 3 ft long. Water and oil (SG=0.75) are poured into the left and right hand portions of the tank to the depths of 2 ft and 4 ft respectively. Assume that water has a specific weight of 62.4 lb/ft³. a) Compute the magnitude of the horizontal forces pushing on the tank. What is the net force? 2 3.464 -D sp g C b) Compute the magnitude of the net vertical forces pushing on each side of the tank.

Name: 3. An 8 ft diameter cylinder weights 500 lb and rests on thebottom of
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: 3. An 8 ft diameter cylinder weights 500 lb and rests on thebottom of a tank that is 3 ft long. Water and oil (SG=0.75)are poured into the left and right hand portions of the tankto the depths of 2 ft and 4 ft respectively. Assume that waterhas a sp

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 62.4 lb/ft. 4ft 8 ft Enter the exact answer. F = lb exact number, no tolerance
lb The trough below contains a fluid with a specific weight of 54 ft ³ trapezoidal wall below. The measurements are given as follows: A = 3.4 feet B = 2 feet C = 4.9 feet Give your answer in pounds-force. 165 A B Find the total force on the
Question 3 A triangular water trough is "a" metres wide and "a" metres deep, as shown in Figure 3. If the trough is filled with water, calculate the magnitude and location of the resultant force acting on the triangular end plates (shaded in grey). The density of water is 1000 kg/m³ (ignore the atmospheric pressure). Use the value of "a" corresponding to the last digit of your SID from Table 1. "a" m "am Figure 3: Triangular water trough a=7
Pressure 450.50 kPa at depth of 20-m: determine the unit weight in kN/m (UP TO THREE DECIMAL PLACES)
The area of the top side of a piece of sheet metal given below. The sheet metal is submerged horizontally in 9 feet of water. Find the fluid force on the top side. (The weight-density of water is 62.4 pounds per cubic foot.) 35 square feet
A section of a hot water heating system must be suspended. The section ismade from one-inch copper tubing weighing 8.515 pounds. The water insidethe tubing weighs 4.6558 pounds. What is the total weight that must besupported in this section?
The flat surface shown is submerged vertically in water. Find the fluid force against the surface. The weight density of water is 9810 N/m. 6m 5m 8m Enter the exact answer. F = %3D
A vertical triangular plate whose height is 4 m. has its base horizontal at the bottom. The difference in level between the center of gravity and the center of pressure shall be 22 cm. What is the base width of the plate i the water surface total hydrostatic force acting on the plate is 76.28 KN. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in' the final answer: 3
3. a. solve for total hydrostatic force, F. (in kN) b. Solve for the location or point of application of the total hydrostatic force F to the gate. use the water surface as the reference of measurement of depth of location (in m) c. what is the magnitude of the force at point at point A shall be applied to the gate to oppose the solved total hydrostatic force so as to keep the gate on its position? (in kN)
Given that the weight density of water is 9810 N/m3, calculate the fluid force (in Newtons) on a rectangular 1.6m cross times 2m flat plate submerged horizontally in water at a depth of 4m. Give your answer correct to two decimal places without the units. Round your answer to 2 decimal places.
The end plates (isosceles triangles) of the trough shown to the right were designed to withstand a fluid force of 6400 lb. Assuming the density of water is 62.4 lb/ft³, how many cubic feet can the trough hold without exceeding this limitation? What is the value of h, the depth of water that exerts a fluid force of 6400 lb? What is the integral that gives the fluid force exerted on the end of the trough when filled with water to a depth of h? h Sody The maximum volume is ft³. (Round down to the nearest cubic foot.) The value of his (Round to two decimal places as needed.) (-3,14) (0,h) y (ft) (3,14) 14 y 3x x (ft) 0 End view of trough 14 ft 30 ft 6 ft → Dimensional view of trough
1. Solve for the height of fluid a) if the fluid is mercury b) if the fluid is water P = OkPaa