From the image below, and using the given datum, match the variable expressions to their position coordinates, SA, SB and SC, where s A is for block A,$3 is for pulley B, and so is for pulley C. If an expression does not match any position coordinate, then match it to the "None" option.1.k-q2.03.p4. kSADatumbcSCk✓ NoneSBФВAРⒸOF

For the given system find the position coordinates forblock A (SA)Pulley B (SB)Pulley C (SC)

From the image below, and using the given datum, match the variable expressions to their position coordinates, SA, SB and SC, where s A is for block A, $3 is for pulley B, and sis for pulley C. If an expression does not match any position coordinate, then match it to the "None" option. 1.k-q 2.0 3.p 4. k SA Datum bc - VSC k None $B B A Р Ⓒon

From the image below, and using the given datum, match the variable expressions to their position coordinates, SA, SB and SC, where s A is for block A, $3 is for pulley B, and sis for pulley C. If an expression does not match any position coordinate, then match it to the "None" option. 1.k-q 2.0 3.p 4. k SA Datum bc - VSC k None $B B A Р Ⓒon

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As the potential across the resistor increased, the current through the resistor increased. If the change in current is proportional to the voltage, the data should be in a straight line and it should go through zero. In these two examples how close is the y-intercept to zero? Is there a proportional relationship between voltage and current? If so, write the equation for each run in the form potential = constant x current. (Use a numerical value for the constant.)
Question 4 List the steps in details to draw the shape below using AutoCAD commands 190 220 50 -90 - 50 114 81 R80 450 122 -R125 68 65 290 50 290 630
Q1. The image below shows an example of "absolute dependent motion analysis", where the motions of two objects depend on each other, and the goal is to find the relations in their motions (i.e., in their positions, velocities, and accelerations). Please put the suggested steps of analysis in the correct order. VA A B VB Differentiate the entire equation with respect to time, and extract the relation in velocities. Repeat for acceleration if needed. Set up a coordinate (s) along the direction of motion from a fixed point (O) or a fixed datum line. Represent the positions of the objects respectively. In some cases intermediate objects need to be considered too and their positions need to be represented as well. Recognize the constant length(s) and find the depending geometric relations between the position variables.
Q2: Write all the necessary steps to draw the following figure using relative coordinate system. For example; the draw of (L1, L2) as following > Dynamic input > of > Home> Draw> Line> 50,50>Enter>@100,0>Enter> @0,50 > Enter> and so on 100 100 100 100 A L1 L2 Start Point (50,50) 100 200 100 007 000 007
9) A merry-go-round is set up at a local fair. The merry-go-round moves continuously at a rate slow enough for riders to step on and off the ride. The pink horse, P, moves along the circumference of the ride. Hal used a coordinate grid to make a rough sketch of the merry-go-round, with the center at the origin. Initially, P is at P(5,0). It takes 30 seconds for P to return to the same place. What would be the coordinate of P on Hal's sketch after 8.25 minutes? P(5,0)
Answer using GRAPHICAL METHOD. Make a representation of the following vector quantities a. A velocity of 20m/s north b. A force of 2000 dynes 45° east of south c. An acceleration of 5m/s2 at 200° d. A displacement of 14m 100° from +x-axis e. A force of 250N at 60° clockwise +x-axis
2. How much money will be accumulated in 20 years from a deposit of $1500 every 6 months if the interest rate is 2.75% per month? Use interpolation to work through your interest rates. S = √₁ + ( x - x ₁) / (ƒ₂- fi) (x₂-x₂) f Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display. Factor value Figure 2-10 Linear interpolation in factor value tables. axis h₂ $₁ Table Unknown Table Known X₁ Required b Linear assumption Known i orn axis ƒ=f₁ +²c=f₁+d C= b
For Questions 3 and 4: A cup of water was heated to a temperature of 90°. It was placed in a refrigerator that had a temperature of 11°C. The water cooled to a temperature of 17°C in 30 minutes. Let the following variables represent the relevant quantities. L = Temperature of the liquid S= Temperature of the surroundings t = Time B = Initial temperature of the liquid (Temperature at t = 0 k = Cooling constant 3. Using the Equation Solver, find the value of k in the equation L = (B - S)e -kt + S. Remember to set the equation equal to zero and then enter it into the Solver.
(xo, Yo) Ay = Number (x,y) CC) 00 BY SA USask Engineering Given the above graph plotting y position against a position, where 0 = 0 m, 30 = -4 m, z = 5 m, and y0 = 0 m, what the change in vertical position over this time interval? Write your answer as an integer. m →X
Q1) Choose the suitable answer [ right v ;or wrong X ] for each of the following: 1. Engineering applications of optimization:-Finding the optimal trajectories of space vehicles. 2. Engineering applications of optimization:-Design of pumps, turbines for maximum efficiency. 3. Engineering applications of optimization:-Controlling the waiting & idle times in production to reduce the produced units. 4. The function f(x) = 0.1 + 0.3 x + x²/(0.1 +x³) is a liner equation with single virable.
2:01 ul 4G 4. A sulms.su.edu.om While constructing a building, an engineer need to fix two steel beams together using a bracket as shown in Figure 1. Using absolute coordinate system, construct a G-code program for drilling hole number 3 only. To remove the metal chips the hole should be done in three equal steps. During the drilling, coolant should be on before spindle starts and stop after spindle stops. The spindle speed set to 1750 RPM. Drilling bit in rack number 2 and it should be 1 mm over the work piece. Drilling feed rate is 20 mm/min. Explain each code used in the program in a column 57.5- 12.5 Hole (4) Hole (3) 30 Hole (1) Hole (2) ΧΟ Υ0ΖΟ All dimensions shown are in mm Figure 1 B. -> 28 •..
QUESTION 2 Consider the following dataset and separator. What is the width of margin (distance between the two paralel lines )? Please use real numbers instead of rations. Eg, f your result is1/2, enter 0.5 w.x+b = +1 w.x+b =0 w.x+b= -1 2.0 0. 05 VW.w