For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 35 kN, F2 = 35 kN, F3 = 50 kN, F4 = 35 kN, and M = 140 kN-m. A 6m H B 5 Answers: x-axis: x= 8 m Equation of line: y = i y-axis: y = i F₂ --x B M D F₁ - F, m m x+ Mi m

For the truss loaded as shown, determine the equation for the line of action of the stand-alone resultant R and state the coordinates of the points on the x- and y-axes through which the line of action passes. All triangles are 3-4-5. Assume F₁ = 35 kN, F2 = 35 kN, F3 = 50 kN, F4 = 35 kN, and M = 140 kN-m. A 6m H B 5 Answers: x-axis: x= 8 m Equation of line: y = i y-axis: y = i F₂ --x B M D F₁ - F, m m x+ Mi m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q3] For the given beam, neglecting self weight, find: (1) The equation of the deflection curve. (2) The maximum deflection. (3) The bending moment at the fixed end. (4) The value of the expression: EI.D'y-P.D²y. lle L=3 m EI-6000 kN.m² W=120 kN P=60 kN
A beam is loaded and supported as shown. (a) Use the double-integration method to determine the reactions at supports A and C. (b) Draw the shear-force and bending-moment diagrams for the beam. Assume w = 16 kN/m, L = 14.0m and El - 5.5x 104 kN-m? is constant for the beam. %3D A -L/2- Part 1 Cut a cross-section through the beam between points A and B, and draw a free body diagram to the left of the cut. Determine an expression for M(x) in section AB of the beam. Check your expression by calculating Mat x-3,5 m. M(x) A Answer: M(x) - kN-m + mA, eTextbook and Media
From the given set of forces shown, the three forces acting on the beam can be replaced with a single equivalent Force R. Determine the following: P,= 25ヒN Pz - 40KN Pa- 80 kN 40° 500 4m Com a. The x-component of the resultant force? b. The magnitude R. c. The corresponding value of e.
2. Determine the location of the center of gravity of a wire with uniform cross- sectional area and specific weight., shown in the figure below. The wire is in the form of a broken line P, P2 P3 P4, with P:(-3, 7), P2(-1, 1), P3 (3, 5) and P. (5, 3). C.G. (0.30, 3.60) Pi-3, 7) P(3, 5) M(-2, 4) 8 M5(1, 3) XM(4, 4) PA(5, 3) P2(-1, 1)
%3D The truss structure (all members have the same area) carry the loading shown (P = 150 kN) Determine the minimum thickness t (in mm) of the steel member considering allowable vertical displacement of C to be 12mm. Use E=200 GPa. Use Virtual Work Method to solve the problem. t E D = 200mm 3m C PV 4m 4m B
9 Consider the plane truss with load Pas shown in the figure. Let the horizontal and vertical reactions at the joint B be Hg and V, respectively and Vc be vertical reaction at the joint C. 2 exhoM S SLO 60° - II B A 60° D L 60° F 60° KLA G P с Which one of the following sets gives the correct values of VB, HB and V? (a) VB = 0; HB = 0; Vc = P (b) VB P/2; HB = 0; Vc = P/2 (c) VB = P/2; HB = P (sin60°); Vc = P/2 (d) VB = P; HB = P (cos(60°); Vc = 0 [2016
Asap
The rigid bar ABC supports a point load P at point A and is being supported by bronze bars BD & CE. For bronze, E = 83 GPa. Determine 4 m 2 m A the maximum allowable load P if the vertical deflection of point A is limited to 1 mm. The areas of bars BD and CE are 1020 mm? and 520 mm?, respectively. 3 m P 3.5 m Assume no bending for all bars. D А. РМАХ (N)
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel. 04. A 35° 35° SUMMARY OF ANSWERS 2.5 m 2.5 m Ус mm C 15 kN CS Scanned with CamScanner
A flat steel plate is of trapezoidal form and uniform thickness of 10mm. The plate tapers uniformly from a width of 150mm to 100 mm over a length of 500mm. Determine the elongation of the plate under an axial pull of 100 KN. Take E= 200 KN/mm² B₁ 100 KN I -x-8x 100 mm 500 mm- 150 mm B₂ 100KN
A beam assembly shown below is supported by a simple hinge and roller supports at A and C respectively. The 8-ft-long segment A-C (a = 4 ft) has a uniform cross section as shown in the figure, right (cross section at e-e). The beam assembly is subjected to a concentrated load (P = 3 kip) at point D, which is directly above point A. Take E = 31500 ksi. D e e R Cross section at e---e 46 3b b Ab 4b Figure 4: Simply supported beam with point load and cross-section If the maximum tensile and compressive bending stresses in the segment A-C cannot exceed ±100 ksi without failure, respectively, determine the smallest allowable dimension b in the segment cross section (see cross section at e-e above, which applies to the whole segment AC). Use F.S. = 2.
The beam in the figure below is subjected to a load at its end. Determine the displacement at C. El is constant. 4 KN ↓ B 2 m (a) 12 13a EXD04 1m X₂ Tºc