The rigid bar ABC supports a point load P at point A and is being supported by bronze bars BD & CE. For bronze, E = 83 GPa. Determine 4 m 2 m A the maximum allowable load P if the vertical deflection of point A is limited to 1 mm. The areas of bars BD and CE are 1020 mm? and 520 mm?, respectively. 3 m P 3.5 m Assume no bending for all bars. D А. РМАХ (N)

The rigid bar ABC supports a point load P at point A and is being supported by bronze bars BD & CE. For bronze, E = 83 GPa. Determine 4 m 2 m A the maximum allowable load P if the vertical deflection of point A is limited to 1 mm. The areas of bars BD and CE are 1020 mm? and 520 mm?, respectively. 3 m P 3.5 m Assume no bending for all bars. D А. РМАХ (N)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

LL Determine the deflection (negative if downward) of the beam at B. Use G-200 GPa and I= 500(10)6 mm. Answer in mm rounded-off to 2 decimal places. P = 29 KN 144H 3 m- P B - - 4 m 2P C H -3 m- acer
2.27 Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm². Link CE is made of aluminum (E = 72 GPa) and has a cross-sectional area of 300 mm². Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.35 mm. Q Search P A 125 mm D B (7 = 225 mm 225 mm 150 mm ↓ E 4) 8:51 AM 3/5/2023
> A Pinned- T -15 ft- 2 k/ff V V Roller утв -6ff- EI = Constant E = 29,000 ksi I = 3,500 in 4 Find: Maximum Vertical Deflection in the beam Method Ć unsupported joint using conjugate beam 2/9
2.28 Each of the four vertical links connecting the two rigid horizontal members is made of aluminum (E = 70 GPa) and has a uniform rectangular cross section of 10 × 40 mm. For the loading shown, determine the deflection of (a) point E, (b) point F, (c) point G. A 250 mm 40 mm. B 400 mm Q Search F 250 mm hn D 300 mm 24 KN T
2.27 Link BD is made of brass (E 105 GPa) and has a cross-sectional area of 240 mm². Link CE is made of aluminum (E = 72 GPa) and has a cross-sectional area of 300 mm². Knowing that they support rigid member ABC, determine the maximum force P that can be applied vertically at point A if the deflection of A is not to exceed 0.35 mm. Q Search. P A 125 mm H D B 225 mm 225 mm C 150 mm E 8:51 AM 3/5/2023
The rigid bar AD is supported by two steel wires of 1/16 in. diameter (E = 29 x 10° psi) and a pin and bracket at A. Knowing that the wires were initially taut, determine (a) the additional tension in each wire when a 220-lb load P is applied at D. (b) the corresponding deflection of point D. F 8 in. E 10 in. -A B D 12 in. 12 in. 12 in. Answer for (a), Pe = Ib, PcF = Ib Answer for (b), ôp = inches (magnitude only) Note: use up to 3 significant figures
Determine the Vertical Deflection at the hinge. The elastic curve may be right or wrong. Indicate the negative sign if the answer is downward Determine the Vertical Deflection at the hinge 1O Kt E 29X103 Ksi I= 80 in4 5 k 6K O-8T internal hinge ー.2エ 3'
Fre. '-- -::) Rod AB is made of aluminum (E - 10.4 x 106 psi). Rod BC is made of steel (E = 29 x 10° psi). Find the force which must be applied at point B so that the net deflection of point A is ZERO. 20 in 24 in C 8 k A В F = ? diameter 3 in diameter
Q2/Find the vertical deflection of joint c (use Unit Load). E=200*10³ kN/mm², A-301 mm² ,short (AB)=5mm 4m B 3m C 10kN
8-33 Determine the slope at B and the menimum deflection pin. I=500in.Use the o 4 the beam. Assome A is a roller and Bisa Take E- 29x10ksi conjugate bean method. 4k 2k 10 Et K- 101t 10 tt t
JC = For the beam and loading shown, determine (a) the deflection at C, PL 0 A P Bt² 2 EI (b) the slope at end 4. PL ↑P -L/3L/3L13 EI D
The rigid bar is supported by the pin-connected rod CB that has a cross-sectional area of 14 mm2 and is made from 6061-T6 aluminum. Determine the vertical deflection of the bar at D when the distributed load is applied.