For the plane composite area shown in the figure, determine the coordinates of the centroid of the shaded area. Determine the coordinate X in [mm). Determine the coordinate Y in (mm). (Identify clearly your working areas) Note: Detail calculations are required in your answers. Jumping to the final answer and omitting to present details of your solution will not be graded and considered NIL. 200 mm 200 mm 150 mm- 125 mm 60 mm 126 mm

For the plane composite area shown in the figure, determine the coordinates of the centroid of the shaded area. Determine the coordinate X in [mm). Determine the coordinate Y in (mm). (Identify clearly your working areas) Note: Detail calculations are required in your answers. Jumping to the final answer and omitting to present details of your solution will not be graded and considered NIL. 200 mm 200 mm 150 mm- 125 mm 60 mm 126 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the composite area shown, calculate the moment of inertia about X and Y axes. 95 mm Ŕ = 60 mm 55 mm 35 mm 70 mm 80 mm 125 mm
7:50 ul LTE O A docs.google.com Choose the correct answer * During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L,) is 2.625 inches. Answer the questions below: Us 70 Tk LyP IR 50- FL PL ptiel linit AL or 6T P EL lastie lii UP per yied paint Lypi Lewer s us t uni mated streagth IR: Indicatul siregh Rupture TR True strugth Ruple fPL (propartimal timt) Direct strain & to to E strmin Cin/in) a b 1. Mild steel is: (a) brittle materials (b) ductile material (c) between the ductile and the brittle 2. Young's Modulus evaluates elasticity within the region from: (а) 0 - Proportional Limit. (b) Proportional Limit - Lower yield Point. (c) Lower
Question 31 Is the sample in the image softwood or hardwood? 100 O a. Softwood b. Hardwood
Kindly select the correct answer with solutions or explanations
The moisture content test is performed on a wood specimen and the results are found as following: Mass of wood specimen in green condition: 323.0 g Mass of oven-dry specimen: 226 g Find the moisture content of the green wood.
Subject is properties of behavior
the composite area shown in the figure below is composed of two rectangles. use b = 4.97m., h = 3.73 m. and t =1.48m. determine the radius of gyration about the indicated x-axis.
Describe with examples the young’s modulus, shear modulus and bulk modulus.
Question 17) The following measurements were recorded during compression test on two specimens: Mild steel and Cast Iron. The width and thickness of the specimen before the test are given in the table below (every dimension was measured three times) Cross-Section Dimensions (mm) Steel Cast Iron Measure #1 w= 12.66, t=12.67 w= 12.67, t=12.67 Measure #2 w= 12.67, t-12.67 w= 12.66, t=12.65 Measure #3 w- 12.68, t-12.67 w- 12.64, t-12.67 Calculate the average width (w) and thickness (t) in mm of both mild steel and cast- iron respectively. The order is w, t (mild steel), w, t (cast-iron) (Use two decimal places. do not add units, e.g. 10.02) With reference to data in question 17, what is the original cross section areas (Ao) of the mild steel and cast-iron respectively. (Use two decimal places, without units, e.g., 120.52)
Considering the composite object given a) Determine the moment of inertia components (Ix, Iy and Ixy) about the x-y axes. b) Determine the principle moment of inertia components and the direction of principle axes by using Mohr's Circle. 0.5m 1.5 m 1.5 m 0.5 m 1 m 2 m 1m 2 m 2m y
Please answer complete question
For the composite area shown in Figure 4.1a, determine the y-coordinate of its centroid. Given B = 450 mm, D = 150 mm, t; = 24 mm, tw1 = 30 mm and tw2 = 45 mm. The positive x and y axes of the coordination system are shown in the figure. B D |-tw1+ - twz