Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 150MPa and the allowable bearing stress for the wood is 28MPa. Assume that the hole in the washers has the same diameter as the bolt. -2 m 3 kN 2 kN 1.5 kN 2 m--1.5 m-i-1.5 m-1-1.5 m--1.5 m- B D

Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 150MPa and the allowable bearing stress for the wood is 28MPa. Assume that the hole in the washers has the same diameter as the bolt. -2 m 3 kN 2 kN 1.5 kN 2 m--1.5 m-i-1.5 m-1-1.5 m--1.5 m- B D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Name: Time you spent to solve the problem HW- 3 ID.: 'Dėtërminë thé forċés in all the members, and state if these memibers are in tension or compression. Use table to arrange your Cal&tlations, show the results on the truss ( if not your witf täke zerở)** 30 N 4m 3 т 15
The lap joint is connected together using a 32 mm diameter bolt. Determine the permanent shear strain in the shear plane of the bolt when the applied force P = 750 kN is removed. Note: The bolt is made from a material having a shear stress-strain diagram as follows T (MPa) A { 600 400 5 50 y (10³ rad)
5. The rod bar shown has steel, brass, and aluminum sections. Axial loads are applied at cross sections A, B, C and D. The allowable stresses are 125 MPa in steel, 70 MPa in the brass, and 85 MPa in the aluminum. Assume that the allowable stresses are the same for tension (T) and compression (C). (a) Determine the diameter required for the brass bar. (b) Determine the required diameter for the steel bar. (c) Determine the required diameter for the aluminum bar. Express your answer in millimeters. Steel Brass C Aluminum B A 100 kN 85 kN 200 kN 215 kN 0.5 m 0.5 m 0.5 m
Problem 50 Two forces of magnitude T, = 10kips and Tc =15kips are applied as shown to a welded connection. Knowing that the connection is in equilibrium, determine the magnitudes of the forces T, and Tp-
A steel cantilever beam is fabricated from two structural tees welded together, as shown in the figure. For this beam, the allowable bending stress is 150 MPa, the allowable shear stress of the steel is 100 MPa, and the allowable shear flow along the weld is 2MN/m. Determine the allowable force P that the beam can carry. (All dimensions are in mm).
Assume that the clamp shown has been tightened on wooden planks being glued together until P = 420 N. Determine the stress in A and D Find the location of the neutral axis
A steel beam is bolted to a steel girder by a connection similar to that in the figure shown below. The diameter of the bolt is 10 mm, and the thickness of each angle bar is 4 mm. For each bolt, assume that the allowable bearing stress is 224 MPa. Find the allowable load in kN on the connection. Assume the thickness of the web of the beam to be 7 mm and the thickness of the web of the girder to be 8 mm The final answer should include two decimal places
(2) 4 0 5 211 5 4 #9 4 "1 16 #3" ft-k fé = 3 ksi, M = 90 NWC. The section is cracked. Computer the bending stresses in the beam by using transformed-area metho
The question is below.