For the frame shown in figure below. Determine the reactions at A, C, and F. 30 kN/m 15 kN/m C D 3m 4m B 9m 8m E 5m 10 kN 3m

Q: Situation #3: Determine the magnitude of the reactions RA, Rs and Rp. hinge 800N 2m 250N/M A 3m 2m…

A:

Q: The 6 m uniform rod as shown below weighs 1000 N. Segment AB and BC is 4 m long. The cable acts at a…

A:

Q: Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the…

A:

Q: Three forces are applied to a bracket as shown in figure. Determine the support reactions at the…

A: Solution:

Q: Determine the reactions at points of contact A, B, and C needed to support the force of 800 N.…

A: To find reaction at point A, B and C

Q: Q.1) For the frame shown in figure, determine the horizontal and vertical components of 6 cm -9…

A: According to the information we have reaction pin at A, B, D, and roller E  for the vertical and…

Q: Q4) Determine the horizontal and vertical components of reaction on the beam caused by the pin at B…

A: The reaction at the point A will be in the vertical direction only and it can be determined as,

Q: 05: A railway bridge consisting of a truss construction as shown in the Figure 3, this truss is…

A:

Q: Determinc the (a) magnitude P the force which the man must cxcrt to the handle of the high-pressure…

A:

Q: The reaction at the support B of the beam shown in below figure is 2 EN 3 kN B 45° 2 m 2 m 2 m 3 m 2…

A:

Q: PROBLEM: Detemine the tension in each cord in the figure showm. 32° 45° 525N 389 N 62° 55

A: Draw the free body diagram of 389 N mass. Consider the equilibrium of vertical forces. T1-389…

Q: The cables shown in the figure are used to support a 40-lb crate. Determine the reaction of cable…

A:

Q: determine horizontal and vertical reaction for the figure as shown A 2 m 45% B 2 m 2 m 2 m F F F

A: In above frame asked about horizontal and vertical reactions for which we need to apply equilibrium…

Q: The square plate shown in Figure 4 is pinned at point O and is supported by a block at point of.…

A: Given:   Mass of the square plate, m=100 kg

Q: Determine the reactions at the supports. 5 kN/m 12 kN 30° Figure 1 D B C 4 m 2 m 2 m

A: Given Data⇒

Q: Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the…

A:

Q: A member is loaded with force system as shown in figure. Find the Moment about A, B,C, D and E Where…

A:

Q: Determine the z, y and z components of reaction at the fixed support A using scalar notation Express…

A:

Q: Neglecting friction and the radius of the pulley. determine the reaction at C. D 150 mm |B 120 N |A…

A: Answer: ◆ The reaction at C is 224 N acting at 2.05°. ◆ Therefore, the correct answer is option (c).

Q: Determine the reactions at the supports. 5 kN/m 12 kN Figure 1 4 m 2m 2 m

A:

Q: Draw F.B.D then find reactions at supports A and B take AB weight 25Kg

A: Given data; Mass of the rod AB, m = 25 kg. Draw a free-body diagram of the rod AB. Calculate the…

Q: Q2- For the frame shown in Figure (2), determine the reactions at A and C.

A:

Q: 20 ft B 12 ft 10 k C H 12 ft 10 k D G 14 ft 10 k VE 6 ft 6 ft 4 ft A 4 ft

A:

Q: Determine the force in members EG, HG, and HJ in the given frame as shown in figure 1 using Method…

A: The slop of BJ, =2.62-0.469.6=0.225 Length of HG = 2.08 m Due to symmetrical loading Ax=0Ay=Iy=4 kN…

Q: 2. The center diagonal of the truss in the figure shown can support tension only. Compute the for DG…

A: To find force in member DG and BE

Q: In the frame below, calculate for the forces (N) in links: GB, FA, HE and GD (Also draw the FBD of…

A:

Q: H.W Determine the support reactions for the trusses shown in the figure 20 k 20 k 20 k В D 8 ft G. F…

A: Find the reactions.

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.