2 k/ft 8 k B CENTI -12 ft-8 ft-9 ft 12 ft-----9 ft- 4 ft 3 ft 3 k/ft с 3 ft D

Q: This still doesnt answer how to get points 2,  2', and 1', so how did you get it?

A: Itis asked to explain how the state points 2, 2' and 1' are obtained

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: 5m %3D d=9·8\ mls? १त्र वह w Given data

A: Given data : The value of mass=m The value of acceleration due to gravity=g The value of height=h…

Q: Are you able to show an answer in terms of using formula from start to finish to get the answer…

A: Are you able to show an answer in terms of using formula from start to finish to get the answer…

Q: Please make draw the right-side view, front view, and top view of the given isometric drawing.…

A:

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: The total positional tolerance equals the sum of the tolerance. O bonus and plus/minus O limit and…

A: According to the given data, we need to fill in the blank part.

Q: please answer final two parts thank you

A:

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: What are the different types of force? Applied Tension Gravitational Spring Air Resistance Normal…

A: (I) Force has been classified on the basis of contact which is as follow 1. Contact force:- These…

Q: Draw back the drawing given  with the scale 1:1 on the new drawing paper using all the method on…

A: 1. First off all we need to locate the two points of the given part at distance of 200 mm apart in…

Q: Show your steps and label units on all answers. 1.) Determine the Forces in all the members, and the…

A:

Q: Please give the answer as in the format asked

A:

Q: A 70 kg skier that moves from rest at A is shown in Figure Q2. Suppose friction can be neglected…

A: Given:m=70 kgθ=30°θ=40°Height AB=12mTo find:-1) Velocity VB2) The istance S

Q: Determine the forces in members BC and CF of the loaded truss. Enter a positive number if in…

A:

Q: For the given isometric drawing, draw the corresponding top, front, and right side view. L HRP FRP L…

A: For the given isometric drawing, draw the corresponding top, front, and right side view.

Q: Please answer questions 7,8, show reasons and examples

A: The characteristic equation of the system is:x^6 + (73*x^5)/40 + (1969*x^4)/48 + (22309*x^3)/600 +…

Q: Subject Date : الموافق 2x92-0 م 24 find divgrad df) 2 19 - موضوع التاريخ

A:

Q: I need answers for 7,8, and 9,

A: A 0.250”X0.250” square hole.

Q: for Part V) should the answer not be -0.4 to the final part of the question since the number put…

A: We have, general equation of the system as x=4.23sin100πt-1.79cos100πt We can write it in the…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: Part C - Maximum allowable axial force for fixed-and-free-end support If the cylindrical column is…

A:

Q: Read the following statement and choose the most appropriate answers. Statement 1 For a measuring…

A: Accuracy is defined as how close is the measured value to the true value.

Q: On the toleranced rectangle below, state the tolerance within which the top surface must be flat. O…

A:

Q: Can you solve the problem again by taking the scale factor 13 ? Can you also draw the graphs…

A:

Q: There are two samples, A and B, ere tested by Rockwell hardness test. Sample A is tested in B scale,…

A: HRB means the Hardness Rockwell B scale HRB means the Hardness Rockwell F scale

Q: G R.75 00.63 THRU 01.123 F0.250 1.00 chamfer with distance 0.25 mm fillet with radius 0.25 mm fillet…

A: Select the correct statement about the notation circled in green and marked as letter F. Assume all…

Q: 1. 1. Which part has the longest length? 2. 2. Which part has the smallest tolerance for the outside…

A: As this question contains multiple parts, solution is provided for first three parts as per policy.…

Q: Develop the general equation of continuity for three-dimensional flow of a compressible fluid for…

A: (a) The expression for the mass entering the given element in the x-direction can be written as,…

Q: There are several failure modes by which gears can fail. Select the true statement from among the…

A:

Q: I need help answering this Review Activity

A: Hello, thanks for the question. Since we only answer up to 3 sub-parts, we’ll answer the first 3.…

Q: Quenching is a process that can reduce the grain size and form a lot of grain boundaries in the…

A: Quenching: In this process metal is heated above its recrystallization and than cool it rapidly. The…

Q: With reference to the drawing callout in Figure 4 below, which part(s) would 'pass' or 'fail'…

A:

Q: Round number to three significant figures. 0.000045389

A: Given data: The given number is N = 0.000045389. Here, there are a total of 5 significant figures.…

Q: 1. A field measures 10 x 15 cm (W x L) at 100cm SSD. What is the field size measurement at 128 cm…

A: In first field measurement, write the given data. W1=10 cmL1=15 cmSSD1=100 cmSSD2=128 cm

Q: Question 3 The figures (1&2) shows a Hole-Pattern as drawn and as inspected. fill table 1 and…

A:

Free undamped vibrations

Whenever an object/system displaces in either side of its equilibrium position with the help of an external/internal means, then the object/system moves regularly or randomly on both sides of its equilibrium position. This motion is called vibration. Generally, there are three types of vibration: longitudinal vibration, transverse vibration, and torsional vibration.