Find the reactions at the supports for the beam that weighs 10 kN shown below. The length of the beam is 10m. 产門 20KN 15KN |12kN 2m 2m 2m

Q: 3a) Calculate the moment produced by F with respect to point B in Nm. Yanıt: 3b) Determine the…

A:

Q: Problem-2 The tension in the guy wire is 2500 N. Determine: a) components Fx, Fy , Fz of the force…

A:

Q: C 1m-2m- B 400 N-m 60° F₁ 2m 3m F₂ -3m D 250 N

A: Given,

Q: Q1-B- Draw just the Free Body Diagram of the following figures. 30 kN/m - 3 m - 3 m - 3 m --- 4 kN/m…

A:

Q: Determine the maximum value of b (lb/ft) if the roller at point A can only support upto 148 lb. The…

A:

Q: Q3 - Determine the reactions at A and B. in the Figure 7. 9 kN 5 kN/m 2m 15m 20 KN 15m 4 kN/m 2MM

A:

Q: Determine the (f_R, By using Law of cosine when ( A=8 lb, B=6 lb, c = 100°) .A 10 .B 11lb .C 10.8lb…

A:

Q: Determine the (f_y) when distance of y = 6.7 mm and the scale of force 30.55 lb/mm

A: Given:distance, y=6.7 mmScale of force, S=30.55 lb/mm

Q: 3. In the figure shown, solve for the distance b. 36 kN 20 kN y 94 kN m 2 m 3 m 2 m

A: Given Data :

Q: Both pulleys are foxed to the shaft and as the shaft turns with constant angular velocity, the power…

A: The angle θ=0

Q: Prove that AXB| ² = A²B² - (A.B)²

A:

Q: 4" Determine the components of F N F = 5 lb 9" G = 10 lb 6" y

A: F = 5 lb

Q: 5. Considering the following design conditions for the beam: Allowable bending stress: 20000 psi…

A:

Q: Solve for A and B. P=400 lbs. 0=30° P 45° B www Drawing not to scale. Use given angles. Magnitude of…

A:

Q: Determine the reactions of the beam. 300 lb 100 lb/ft D1 8' D2 400 lb

A:

Q: The modulus of rigidity is defined as the ratio of shear strain to shear stress. Select one: a.…

A: Option a is correct. The given statement is false.

Q: Determine the extension (m) of the whole system shown if k1 = 14.7 N/m, k2 = 21.23 N/m, k3 = 38.22…

A: To find: The extension of the whole system. Given: The value of stiffness are k1=14.7 Nm,k2=21.23…

Q: 3. A rod with a mass of 5kg and a total length of 2 meters that can spin about an axis through its…

A: Write the given data with suitable variables: M=5 kgL=2 mI=ML212F=10 N

Q: Determinethe magnitude (Ib) of the horizontal component of force at point C if P= 126.6 lb, x = 13.7…

A: There are three static equilibrium equations, horizontal force balance, vertical force balance, and…

Q: Find the force of the rods AB, AC, BC and BD. 20 N 30 N В 4m 4m 4m 4m 4m 4m A 4m E

A:

Q: -2- 6.1Dtanl Hhe mechanical raud the cireuit for the rofationale szotern . b1 Find the drono for…

A:

Q: Resolve the 500-lb of fig. into two components: a shearing component parallel to AB and a normal…

A: In this question, force 500lb is to be resolved along two mutually perpendicular lines, one is…

Q: For the problem shown, determine the magnitude of the force in member EF given that x = 2.3 m, y =…

A:

Q: Consider the pipe shown in (Figure 1). The forces F = 650 N, F = 700 N , and F3 = 700 N are paral…

A:

Q: Q2: Determine (Y). D2 Y Q /sec L (m) D1 D2 220 0.5 5 0.25 D2 Y D1 Hg-

A:

Q: 1-11. An z component of the force F in Fig. P 1-11 is 180 lb to the right through 0. Determine F and…

A:

Q: H G 0° 60 6 kN 6 kN 8 kN Sm Sm Sm Sm

A:

Q: ne of your classmates is tra ackyard and jumped off her rain. The student weighs 12 ne roof's height…

A: The above given question is based upon energy balance of the system at different positions. So, to…

Q: 0. Determine the magnitude g the Resuftot. b. Determine the Pokce g the Reacionsat A C. Determine…

A: Solution:   The magnitude of the resultant and the support reactions at A and B are calculated…

Q: Q1): Determine the general solution of the O.D.E: (1-x) y'-y² =0

A:

Q: Find the resultant force of the following? B. 2 m 3.5 m F = 600 N 0.5 m 450 N 1.5 m 1 m 0.5 m 1.5 m…

A:

Q: shown in Fig. Determine 1-The moment of force F3 about point C. 2-The moment of force F2 about point…

A: Given data: F1 = 1 kN F2 = 1.2 kN F3 = 1.6 kN Need to determine the moment.

Q: Determine the tensions in the belt on pulley B assuming the shaft is running at a constant speed.…

A: Given:T2 = 0.15 T1dA = 8 indB = 7 in To find: T1 and T2

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.