For the beam shown below, construct the Influence diagrams of the following functions: reaction at F, reaction at D and the moment at E. Also calculate the value of the maximum moment at C due to a concentrated load with a magnitude of P (your assigned P). L 1.0 Te www 3.0 3.0 с + D E TOO ww All distances are in meters 4.0 3.0 F A m

For the beam shown below, construct the Influence diagrams of the following functions: reaction at F, reaction at D and the moment at E. Also calculate the value of the maximum moment at C due to a concentrated load with a magnitude of P (your assigned P). L 1.0 Te www 3.0 3.0 с + D E TOO ww All distances are in meters 4.0 3.0 F A m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the reactions at A and B for the given loaded beam in attached Picture. SOLVE ASAP
Ql:- The coplanar force system shown in Figure below is subjected to a couple moment (M) and three forces. Two forces are known in magnitude and direction and shown in the Figure (150 N and 60 N). The third force is passing through the center of the semi-circle (point C). The resultant of all these forces is a single couple (750 N.m) counterclockwise. a) Determine the magnitude and direction of the third force. b) Determine the magnitude of moment (M). c) Replace the couple (M) by two vertical equal forces acting at D and E. d) Replace the force (150 N) by and single force at D and a couple. Radius 5 m 150 N 60 N
A Read aloud V Draw Highlight Question 3 a) In constructing the influence line of an indeterminate beam, the ordinates of a number of points are computed. Is it right to state that Maxwell's law of reciprocal deflections cases the calculation process? Explain. b) For the indeterminate beam in figure 7 the ordinates of the influence line fy support reaction Cy for points A, D, E, F, B, G and C were found to be 0, -0.062, -0.085, -0.052, 0, 0.27, 1.0 respectively. Explain how to determine the ordinates for the support reaction By and moment at E. A. E C. 2m 2m 2m 2m Ay 2m 2m Cy By Figure 7 c) Determine the structural stiffness matrix [k], structural load factor [P] and structural displacement vector [A] of the structure in figure 8. A 4m Figure 8
In the beam depicted above, ?A is a fixed support. The magnitude of ?=365?/?W=365N/m, ?=60?P=60N and all lengths denoted by ?=1.5?a=1.5m. The system is in equilibrium. Using the given sign convention, answer the following questions. a) Calculate the vertical component of the external reaction at ?A in ???????Newtons. b) Calculate the horizontal component of the external reaction at ?A in ???????Newtons. c) Calculate the moment component of the external reaction at ?A in ??????Newton ??????metres. d) Calculate the shear force at point ?B in ???????Newtons. e) Calculate the bending moment at ?B in ??????Newton ??????metres. f) Calculate the shear force at point ?D in ???????Newtons. g) Calculate the bending moment (absolute value) at ?D in ??????Newton ??????metres. h) Calculate the shear force at point ?E in ???????Newtons. i) Calculate the bending moment at ?E in ??????Newton ??????metres. j) Calculate the shear force at point ?H in…
Reactions have been calculated for the beam AB shown in the figure. The shear force at location X (4m to the right of A) is most nearly equal to 6kN 3kN/m A i B VA = 8.4kN Vg = 9.6kN 4m 2m 4m 2m 2m
PROBLEM 2.29 The guy wire BD exerts on the telephone pole AC a force P directed along BD. Knowing that P must have a 720-N component perpendicular to the pole AC, determine (a) the magnitude of the force P, (b) its component along line AC. 7 m 2.4 m
3. For the beam shown below draw the influence lines for By, Dy, VC and MC using the equilibrium method. Find the maximum possible value of MC if a 33KN/m distributed loud and a single 40KN point load may be placed anywhere on the beam B C E 3 m 3 m 3 m 3 m
An AB beam of 1350 N contain a load of 2250 N in B. The beam is maintained by fixed support in A and by the cable CD, which is stuck to a counterweight W. (a) If W = 5850 N, determine the reaction in A. (b) Determine the interval of values of W in order to make the binary's intensity in A don't exceed 2,025 N*m
SITUATION. The tower for a transmission line is modeled by the truss shown. The crossed members in the center section of the truss may be assumed to be capable of supporting tension only. Given: P=2.8kN 8=15⁰ a = 3m b=3m c= 5m 5 panels@(a)m each D E b G P b b K C Zoom image Compute the force induced in member CD. C B
150 mm 60 mn 300 nm 000 m 50 mm 5 m B 25 kNm 5 m 10 KN A beam is created by nailing 3 planks together with 2 rows of nails as shown above. The beam exhibits a pin support at A and is suspended by a cable at B. A concentrated load of 10 kN is applied at the free end while a moment of 25 kNm is applied at location B. a) Determine the second moment of area (I) of the cross-section b) Draw the free body diagram, shear force diagram, and bending moment diagram of the beam c) For the maximum shear force on your SFD, determine the maximum and minimum shear stresses at the interface between the horizontal and vertical planks d) For the maximum shear force on your SFD, Determine the shear stress at the neutral axis
For the beam shown in Figure ( 2), draw the influence line (I.L) for reaction at E, shear force at support C, shear force at D and bending moment at D. Then find the maximum (+ve) bending moment at D due to uniform dead load of (16 kN/m) and uniform live load of (20kN/m) can occupy any length and region of the beam Hinge D E F 我 В 2 m 2 m 2 m 4 m 1m Figure (2)
The left support of a fixed beam having length 3m is rotated by 0.001 radian in the anticlockwise order, Take El = 2 x 1013 Nmm². FEM generated at right support is hogging moment of 20 kN.m sagging moment of 10 kN.m hogging moment of 10 kN.m Osagging moment of 20 kN.m