For low-speed (laminar) steady flow through a circularpipe, as shown in Fig. P1.12, the velocity u varies withradius and takes the formu = B(rở - r?)where u is the fluid viscosity and Ap is the pressure drop fromentrance to exit. What are the dimensions of the constant B?Pipe wallr=rи (г)r= 0P1.12

Using boundary conditions we know that at r=0 , u is maximum So dimensions of all other quantities

Answered: For low-speed (laminar) steady flow…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The velocity distribution in a 0.02 m diameter horizontal pipe conveying carbon tetrachloride (specific gravity = 1.59, absolute viscosity = 9.6 x 10-6 Pa sec) is given by the parabolic equation: v(r)=0.01(0.12- r?), where v(r) is the velocity in (m/s) at a distance r in (m) from the pipe center. What is discharge? O a. 3.13 x-8 m3/s O b. None of the mentioned O c. 1.047 x 108 m3/sec O d. 4.97 x 109 m3/sec
Viscosity can be measured by flow through a thin-bore or capillary tube if the flow rate is low. For length L, (small) diameter D« L, pressure drop Ap, and (low) volume flow rate Q, the formula for viscosity is u = D'Ap/(CLQ), where C is a constant. (a) Verify that C is dimensionless. The following data are for water flowing through a 2-mm-diameter tube which is 1 meter long. The pressure drop is held constant at Ap = 5 kPa. T, °C 10.0 40.0 70.0 Q, L/min 0.091 0.179 0.292 (b) Using proper SI units, determine an average value of C by accounting for the variation with temperature of the viscosity of water.
An incompressible fluid (kinematic viscosity, 7.4 x10-7 m²/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is rt of this book may be repro
The pressure drop (Ap) test is carried out using a pipe configuration as illustrated below: Manometer 1 Manometer 2 straight pipe D= 2R R= radius in pipe The pipe data and the flowing fluid are as follows: Pipe: D = 1 cm; L= 100 cm. Fluid: Water, with density (A) = 1000 kg/m"; absolute viscosity (u) = 0.001 kg/im.s); Experimental data is shown as shown in the following table: Task: Ja. Plot the graph of the pressure as a function of the average velocity (V.v). b. Based on the equation for laminar flow in the pipe as follows: Ap = 32VuL, Vavg (m/s) Ap (Pa) 0,001 0,002 0,005 0,01 0,02 0,04 0,06 0,08 0,1 0,12 0,15 0,30 0,62 1,61 3,10 6,10 12,10 20,10 26,00 32,50 38,90 47,20 D Compare the experimental results in the table with the results of calculations using the above equation. Leave a comment. Note: Ap = p1-p2. c. The coefficient of friction (f) in the pipe is formulated as follows: f- 2DAD PL(V.) plot (plot) this distribution of fas a function of the Reynolds number (Re). Re is…
QA An incompressible fluid (kinematic viscosity, 7.4 x10-7 m2/s, specific gravity, 0.88) is held between two parallel plates. If the top plate is moved with a velocity of 0.5 m/s while the bottom one is held stationary, the fluid attains a linear velocity profile in the gap of 0.5 mm between these plates; the shear stress in Pascals on the surface of top plate is (a) 0.651 x 10-3 (c) 6.51 (b) 0.651 (d) 0.651 x 103
Problems H.pdf > Problems H.W: Lecture No.6 Part 2 Q1-(2.4-4, Holland): A fluid of density (p) and dynamic viscosity (u) flows in s.s in a cylindrical pipe of inside diameter (d) with mean linear velocity (u). Derive an expression for the pressure gradient AP/L in terms of p, u, d & u. By dimensional analysis (Note Lect. No.3). Q2-An oil with a viscosity of u= 0.40 N-s/m and density p= 900 kg/m flows in a pipe of diameter d= 0.20m. (a) What pressure drop, pl-p2, is needed to produce a flowrate of Q=2.0x10-5 m/s if the pipe is horizontal with xl=0 and x2=10 m? (b) How steep a hill, part (a), but with pl=p2? (c) For the conditions of part (b), if pl=200 kPa, what is the pressure at section, x3=5 m, where x is measured along the pipe? „must the pipe be on if the oil is to flow through the pipe at the same rate as in II
Velocity distribution of a fluid in a sliding plate viscometer is used to measure the viscosity of the fluid. The top plate is moving with force (F) with a constant velocity (V) as shown in the Figure below. Force (Ft)= 5 N, Velocity (V) = 10 m/s, Temperature = 100°F. Top plate (Area » Length = 0.1 m and width = 0.05 m spaced by 0.001 m) is moving and the bottom plate is stationary. Determine: The viscosity of the fluid. Which fluid is this? Is this fluid more, or less viscous than water? ● IN FLOW N-L
C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
C1 (a). A lubricating oil having the dynamic viscosity of 0.058 poise and specific gravity of 1.11. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3,(iii) the kinematic viscosity in stokes, and (iv) the specific volume in m³/kg. C1 (b). The capillary effect in a glass tube of 2.6 mm diameter, when immersed in (1) water and (2) mercury are 7.4 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a).(i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m³/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
The laminar flow of a fluid with a constant viscosity, 4, inside a channel is governed by the following boundary value problem (strong form): d'u dp for y E (0, h) "dy dr u = 0 at y = 0 and y = h vhere u is the fluid velocity and is the pressure drop in the direction of the flow. a) Derive the weak form of the boundary value problem described above.
Oil (dynamic viscosity) between a block of mass M (5 kg) and the substrate(μ = 1.6 Pa.s), oil film thickness (h = 0.7 mm)). Block base surfaceIts area is given as A = 28 cm2. Block m (1kg weight) with a wire ropeIt depends on the mass. At time t = 0, mass m is released. According to these data;a) Find the viscous forces when the block moves with V = 1 m / s velocity.b) Derive an equation for the block velocity as a function of time (t).c) Plot the velocity-time variation for t = 0 and t = t.
An oil has a kinematic viscosity of 1.25 E-4 m 2 /s and aspecifi c gravity of 0.80. What is its dynamic (absolute)viscosity in kg/(m ∙ s)?( a ) 0.08, ( b ) 0.10, ( c ) 0.125, ( d ) 1.0, ( e ) 1.25

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS