For determining the %w/w of salicylamide and caffeine in an unknown sample using acetaminophen as an internal standard using a HPLC a) Is it possible to use the λmax (273 nm) of caffeine in the experiment instead of using 254 nm? Explain your reasoning. b) What are some advantages of using the Internal

For determining the %w/w of salicylamide and caffeine in an unknown sample using acetaminophen as an internal standard using a HPLC a) Is it possible to use the λmax (273 nm) of caffeine in the experiment instead of using 254 nm? Explain your reasoning. b) What are some advantages of using the Internal

Principles of Instrumental Analysis

7th Edition

ISBN:9781305577213

Author:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Publisher:Douglas A. Skoog, F. James Holler, Stanley R. Crouch

Chapter1: Introduction

Section: Chapter Questions

Problem 1.9QAP

See similar textbooks

Similar questions

What is the significance of the max of a spectrum? What are the other uses of the spectrophotometer?
Suppose you are analyzing mercury ions (Hg2+) in drinking water samples with atomic absorption spectroscopy. If the Hg2+ signal varies by a matrix of sample, which of the following should be used as a standard for calibration? Either cations or anions can be used if they are different from Hg2+, 0 H20 Any anions can be used if they are different from Hg2+ Any cations can be used if they are different from Hg?". Hg2+
The levels of Vitamin B1 in a sample of milk was determined using the Standard Addition method and technique of fluorescence spectroscopy. 18.0 ml of the milk sample was diluted to 20.0 ml using distilled water and then the fluorescence was measured. The resulting signal was 210 units. A spike was made by taking 18.0 ml of the same milk sample, adding 1.0 ml of a 6.0 ppm Vitamin B1 standard solution, and then diluting to 20.0 ml using distilled water. The signal of the spiked milk was 540 units. Calculate the concentration of Vitamin B1 in the original milk sample (in ppm). Report to 3 decimal places.
Suppose a student is preparing a set of standard solutions for use in a spectrophotometric study. If percent transmittance, %T, were measured in the standard solutions before the color had a chance to fully develop, the measured value would be compared with solutions that have allowed the color to fully develop.
For the determination of Fe3 +, 25 mL of sample taken from sea water is diluted to 100 mL and a quantity of the obtained solution is taken and Fe3 + is determined by atomic absorption spectrophotometer. The absorbance values of the standard and sample solutions are below, and calculate the Fe3 + concentration in sea water in mg / L by drawing the relevant graph.Solution Absorbance1 mg / L Fe3 + 0.04095 mg / L Fe3 + 0.205110 mg / L Fe3 + 0.411615 mg / L Fe3 + 0.620820 mg / L Fe3 + 0.8222Sample Solution 0.5155
What is the relationship between chemical shift in ppm and operating frequency?
1. State the difference between transmittance, absorbance, molar absorptivity, and fluorescence. Which one(s) is proportional to analyte concentration?
Determining the sodium concentration in coffee with flame atomic absorption spectroscopy (FAAS) can be challenging due to interferences. To overcome these interferences, lithium is commonly used as an internal standard. A researcher prepared a sample with an internal standard (Lit) to analyte (Na+) concentration ratio of 2.00/1.00. The ratio of the internal standard signal to the analyte signal (Li+ signal/Na+ signal) was found to be 1.170/1.000. Determine the response factor, F. F = A sample was then prepared containing 12.70 mL of coffee and 4.80 mL of 5.20 ppm Lit, and diluted to a 50.00 mL total volume. The ratio of the internal standard signal to the analyte signal in the unknown sample was found to be 0.890/1.000 (Li+ signal/Na+ signal). Determine the unknown concentration of Na+ in the coffee sample. [Na+] = ppm
What is the relationship between the excitation wavelength (λex) and emission wavelength (λem) in atomic spectrophotometry (e.g. flame or furnace atomic absorption spectrophotometry)? Why is this different from molecular spectrophotometry?
State True/False for the following statements. 1. In UV-Vis spectrophotometric analysis, the 2.82% transmittance of solution has an absorbance value of 1.55. 2. Peaks resulting transitions from n→ are shifted to shorter wavelengths (blue shift) with an increasing of solvent polarity. 3. In molecular absorption spectrophotometry, the relationship between transmittance and concentration is not linear while the absorbance vs concentration is linear. 4. Beer's Law states that absorbance of a compound is directly proportional to the log of the concentration of the absorbing species. 5. Different colors of the lights are refer to the waves with different amplitudes.
A spectrophotometer method for the quantitative analysis of Pb2+ in blood uses Cu2+ as an internal standard. A standard containing 1.75 ppb Pb2+ and 2.25 ppb Cu2+ yields a signal of 0.832 for Pb2+ and a signal of 0.351 for Cu2+. A sample of blood is spiked with the same concentration of Cu2+, giving a signal of 0.520 for Pb2+ and 0.289 for Cu2+. Determine the concentration of Pb2+ in the sample of blood.
A spectrophotometric method for the quantitative analysis of Fe2+ in blood uses Zn2+ as an internal standard. A sample containing Fe2+ and Zn2+ with final concentration of 3.25 ppb and 0.75 ppb, respectively, that yields a signal of 0.423 for Fe2+ and 0.650 for Zn2+. Subsequently, a sample of blood is spiked with Zn2+ to give the same final concentration and yielded a signal of 0.832 for Zn2+ and 0.110 for the unknown concentration of Fe2+. Determine the concentration of Fe2+ in the sample of blood.