For a belt and 2-pulley system, the pitch diameters of the pulleys are 4 inches and 10 inches.  Larger pulley is the driver.  The center distance is 24 inches.  If the angular speeds of the smaller and larger pulleys are 250 RPM and 100 RPM respectively, determine linear velocity in ft/min.

Q: onsider a pulley system shown below. The coordinate x is the displacement of G. Assume there is no…

A: In the given problem, a single chord connects block and pulley, thus their displacements are…

Q: For a Davis steering gear, the gear's track arm  is at a distance of 160 mm from the front main axle…

A: Data given -  w = 2 m  h = 160 mm  y = 100/2 = 50 mm

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A: Given data Output shaft speed = 2391 rpmOutput shaft torque = 750 Nm For the given gear train, we…

Q: Find the angle of banking for a highway curve of 90 m radius for cars traveling at 128 Km/hr, if the…

A: The given data are: R=90 mv=128 km/hr=35.56 m/sμ=0.4 The free-body diagram of the car on a banked…

Q: A 20-in diameter rotates at 200 RPM and a 40-in diameter pulley is used with an open belt to connect…

A:

Q: pump forces 1.5 m^3/min of water horizontally from an open well to a closed tank where the pressure…

A:

Q: Determine the torque needed to bring a turbine whose moment of inertia of 60 slugs-ft² to rest in…

A: Given that, Moment of inertia  = I= 60 slugs-ft2 Initial speed = Ni=764 rpm Final speed = Nf=0 rpm…

Q: 2) Three cylinder A:B:C has a speed ratio of 3:2:4 are externally in contact to each other. If…

A: Given in question 2:Speed ratio of A,B,C=3:2:4Centre distance between A and C=30 in

Q: When a cyclist pedals, he turns a gear, called a chainring. The angular velocity of the chainring…

A: Given data, Diameter of the rear wheel, DR = 700 mm = 0.7 m Diameter of chainring, DC = 150 mm =…

Q: A multi-cylinder engine is to run at a speed of 600 r.p.m. On drawing the crank-effort diagram to…

A:

Q: Find the center distance in (cm) of 4 direct contact rolling cylinders. Cylinders A-D have a speed…

A:

Q: A 2.5 ft diameter flywheel of a gas engine has a pulley 10 in. in diameter bolted to it (both…

A: a) If the pulley is bolted to the flywheel, then the pulley rotates with the same angular velocity…

Q: In the gear train shown, gear 3 is carried on arm 5. Gear 3 meshes with gear 2 and gear 4. The…

A: Given, T2=60T3=20T4=100N4=151 rpm (counterclockwise)

Q: A balanced rigid disc mounted on a rigid rotor has four identical point masses, each of 10 grams,…

A: Given data: m=10 g=0.001 kgr=100 mm=0.1 mω=10 rad/s Need to determine the magnitude of the resultant…

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A:

Q: Complete the following sentence 1- The center of mass of a rigid body in the form of thin wire…

A:

Q: The figure below shows a sewing needle bar mechanism O1ABO2CD wherein the different dimensions are…

A:

Q: Two cylinders rolling in the same direction has a speed ratio of 4.2. If the diameter of the driven…

A: Hgf

Q: The shown picture is part of automatic gearbox used in car transmission system. If the green shaft…

A:

Q: The wheels of a car have radius 10 in. and are rotating at 700 rpm. Find the speed of the car in…

A: The wheels of a car have radius 10 in. and are rotating at 700 rpm. Find the speed of the car in…

Q: urning moment 1mm = 60 Nm: crank angle, 1 mm = 1° . The turning moment shows the maximum energy that…

A:

Q: A flywheel of radius 0.1 m which is attached with a mass of 800g takes 12 seconds for 2 revolutions.…

A:

Q: A planetary gear train is shown. The ring gear has 50 and is not able to rotate. The number of teeth…

A:

Q: In a chain drive, the speed of the chain is not uniform and varies from a minimum  value to a…

A: The following step must be followed to come to the solution of the given problem:- Giver that:-…

Q: 4. There are two disks: one (A) an engine flywheel, and the other (B) a clutch plate Attached to a…

A: (1) In the absence of the external torque angular momentum remains conserved initial angular…

Q: With the 131 mm diameter pulley A having a counter-clockwise speed of 906 rpm, determine the speed…

A: Given data:-  Speed of pulley A =906 rpm Diameters of pulley A and B = 131 mm Diameter of pulley C =…

Q: Power is to be transmitted from one shaft to the other by means if two rolling cones whose shafts…

A:

Q: Q2A = 12 in.; AB = 2 ft 4 in.; BC = 8 in.; CD = 2 ft; DE = 1 ft 3 in.; Q7E = 12 in.; Q5C = 2 ft; DF…

A: function All DC = all -DCL (device I v customer)ALL DC = cell (1,1)For i = 1 = i 05T1= device If -…

Q: A gear box has an input speed of 1500 rev/min clockwise and an output speed of 300 rev/min…

A:

Q: A lathe having a 5-step pulley is driven by a belt, assumed to be crossed, from a pulley of the same…

A:

Q: The figure shows a rotating geared system. A torque of 3N is applied to an input gear in order to…

A: Given data: Input gear teeth = z = 11 Output gear teeth = Z = 99 Assuming that  Input gear torque =…

Q: Two shafts A and B are connected by rolling cones and turn in the same direction. A makes 250 RPM…

A: Given:- RPM of shaft A, NA=250 RPM of shaft B, NB=90 Shaft angle=30 degrees To find:- Cone angle for…

Q: 1.2. Trucks are used to convey mineral from a stockpile to the metallurgical plant along a level…

A: Given: The total mass of the truck, M = 25 tonne the rolling resistance, R = 240 N/tonne The engine…

Q: For the non-offset slider crank shown in the figure below the crank O2A is rotating at constant…

A:

Q: An engine turns at 250 revolutions per minute and its stroke is 450 mm. Find the average pistol…

A:

Q: In the gear train shown gear 3 is carried on arm 5, Gear 3 meshes with gear 2 and gear 4. The number…

A: Here, Gear 2 is sun gear. Gear 3 is planet gear. Gear 4 is annular gear. Link 5 is arm.   From the…

Q: H.W1 A belt drive system shown, is used as a speed reducer. The input shaft rotates at 2000 rpm and…

A:

Q: Two cylinders rolling in the same direction has speed ratio of 2.5 and center distance of 50 cm.…

A:

Q: The motion transmitted between the teeth of gears in mesh is *

A: The gears are used for transmitting power from one shaft to another shaft. The gear on the driving…

Q: A turns 80 RPM and B 120 RPM are connected by rolling cones. The cones are rolling in opposite…

A: GivenNA=80rpmNB=120rpmshaft angle=45°

Q: The gear train shown in the image has a pressure angle of 20° and a DP of 16. Shaft 2 is turning at…

A: Given dataOutput speed = Speed of gear 5 = N5 = 2391 rpmNumber of teeth of gear 5 = z5 = 20For the…

Q: Two cylinders rolling in the opposite direction has a speed ratio of 3. If the diameter of the…

A:

Q: A gear box has an input speed of 1800 rev/min clockwise and an output speed of 400 rev/min The input…

A: N1=1800 rev/min N2=400 rev/min P1 =25KW η=90% To find  1.Input torque T1  2.The output power P2…

Q: reciprocating steam engine has a stroke of 24 in. and rotates at 300 rpm. Find the linear velocity…

A: Given Data L=24 in  N=300 rpm

Q: The max speed for the servo shown is 130RPM when connected to 6V. Assume that the gearbox on your…

A: Speed can

Q: In a brick-making machine is found this train of gears. A motor carrying pulley E, which is 8 in.…

A: please upload complete question with teeth value. please show daigram fo this qusstion.

Q: A motor-cycle engine crankshaft has an angular velocity of 523.6 rad/s and is in third gear of ratio…

A: Gear Ratio: It is defined as the ratio of output speed to the input speed. Gear ratio (i) = Output…

Q: Q3: (15 marks) Each propeller of the twin-screw ship develops a full-speed thrust of ( 300 kN ). In…

A: Given:  F = 300 kN P = 50 kN distance x is to be calculated.

Q: turbofan compressor blade is 3.0 m long and is rotating at 12350 rpm.  Calculate the following:…

A:

Basic Terminology in Mechanics

The area of science and mathematics concerned the motion of the objects, the relation between the force matter, and motion if specified. Forces exerted over the objects result in displacements or changes in the position of an object concerning its environment. This branch of physics keeps its roots in Ancient Greece in the form of the scripts of Aristotle and Archimedes.