Two parallel shafts A and B, 36 in. apart, are connected by a belt drive. The driving pulley rotates at 250 RPM and the driven pulley at 600 RPM. The smaller pulley diameter is 10 in. Draw the figures or diagrams, and for both open belt and cross belt, determine the following; 1) the diameter of the larger pulley 2) the linear velocity of the belt (ft. / min.), and 3) the length of the belt.

Two parallel shafts A and B, 36 in. apart, are connected by a belt drive. The driving pulley rotates at 250 RPM and the driven pulley at 600 RPM. The smaller pulley diameter is 10 in. Draw the figures or diagrams, and for both open belt and cross belt, determine the following; 1) the diameter of the larger pulley 2) the linear velocity of the belt (ft. / min.), and 3) the length of the belt.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A bicycle with 20-in.-diameter wheels has its gears set so that the chain has a 6-in. radius on the front sprocket and 4-in. radius on the rear sprocket. The cyclist pedals at 175 rpm.Find the linear speed of the bicycle in in/min (correct to at least two decimal places) in/min
A 20-in diameter rotates at 200 RPM and a 40-in diameter pulley are used with an open belt to connect two shafts 6 ft. apart. Determine the length (inches) and speed of the belt (FPM). PLLEASE PROVIDE ILLUSTRATION
For a belt and 2-pulley system, the pitch diameters of the pulleys are 4 inches and 10 inches. Larger pulley is the driver. The center distance is 24 inches. If the angular speeds of the smaller and larger pulleys are 250 RPM and 100 RPM respectively, determine linear velocity in ft/min.
A 20-in diameter rotates at 200 RPM and a 40-in diameter pulley is used with an open belt to connect two shafts 6 ft. apart. Determine the length(inches) and speed of the belt (FPM). Please provide illustration
An engine turns at 250 revolutions per minute and its stroke is 450 mm. Find the average pistol speed in meters per minute, and the speed of the centre of’ the crank pin in meters per minute.
Match the items in columnsI and II. Column I P. Addendum Q. Instantaneous center of velocity R. Section modulus S. Prime circle Column II 1. Cam 2. Beam 3. Linkage 4. Gear (a) P-4, Q-2, R-3, S-1 (b) P-4, Q-3, R-2, S-1 (c) P-3, Q-2, R-1, S-4 (d) P-3, Q-4, R-1, S-2
A lathe having a 5-step pulley is driven by a belt, assumed to be crossed, from a pulley of the same size on the countershaft. The countershaft is to have a constant speed, and the lathe is to have speeds of 60 rpm and 135 rpm when the belt is on the steps either side of the center step. If the minimum speed is 40 rpm and the smallest diameter is 4 in., find theproper speed of the countershaft, maximum speed of the lathe, and the diameter of all steps on the pulleys.
A shaft turning 200 RPM is to drive another shaft at 250 RPM connected in open belt. Find the diameters of the two pulleys, using integral number of inches for each diameter, to give as nearly as possible a belt speed of 3500 FPM.
The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m. to 850 r.p.m. Find the number of teeth on the driven sprocket. If the pitch circle diameter of the driven sprocket is 350 mm and center to center distance between the two sprockets is 1000 mm, determine the pitch and length of the chain.
In the figure shown, If vc=500 mm/s , solve for the (a) velocity (in m/h) of D and (b) the angular velocity (in rpm) of AB. 320 mm C 100 mm 100 mm - 240 mm- B.
two pulleys are connected by a belt. The nubers of RPM of the two pulleys vary inversely as their diameters. A pulley having a diameter of 25cm is turning at 900 rpm. what is the number of RPM of the second pulley wgich has a diameter of 40cm
In the gear train shown, gear 3 is carried on arm 5. Gear 3 meshes with gear 2 and gear 4.The number of teeth on gear 2, 3, and 4 are 60, 20, and 100, respectively. If gear 2 is fixed andgear 4 rotates with an angular velocity of 151 rpm in the counterclockwise direction, theangular speed of arm 5 (in rpm) is