Flow through the converging nozzle in Fig. P4.2 can be approximated by the one-dimensional velocity distribution P4.2 2x v = 0 w=0 L u = Vol 1 + (a) Find a general expression for the fluid acceleration in the nozzle. (b) For the specific case Vo = 10 ft/s and L = 6 in, compute the acceleration, in g's, at the entrance and at the exit. %3D Vo u = = 3Vo x = L P4.2 x = 0

Flow through the converging nozzle in Fig. P4.2 can be approximated by the one-dimensional velocity distribution P4.2 2x v = 0 w=0 L u = Vol 1 + (a) Find a general expression for the fluid acceleration in the nozzle. (b) For the specific case Vo = 10 ft/s and L = 6 in, compute the acceleration, in g's, at the entrance and at the exit. %3D Vo u = = 3Vo x = L P4.2 x = 0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In Prob. it would be difficult to solve for Ω because of itappears in all three of the dimensionless pump coefficients.Suppose that, in Prob. 5.61, Ω is unknown but D = 12 cmand Q = 25 m 3 /h. The fluid is gasoline at 20 ° C. Rescale thecoefficients, , to make a plot ofdimensionless power versus dimensionless rotation speed.Enter this plot to find the maximum rotation speed Ωforwhich the power will not exceed 300 W.
The Reynolds transport theorem (RTT) is discussed in Chap. 4 of your textbook. For the general case of a moving and/or deforming control volume, we write the RTT as follows: d pb dV + pbV-ñ dA dt dt dB sys where Vr is the relative velocity, i.e., the velocity of the fluid relative to the control surface. Write the primary dimensions of each additive term in the equation and verify that the equation is dimensionally homogeneous. Show all your work. (Hint: Since B can be any property of the flow-scalar, vector, or even tensor—it can have a variety of dimensions. So, just let the dimensions of B be those of B itself, {B}. Also, b is defined as B per unit mass.)
A proposed harmonic function F(x, y, z) is given byF = 2x2 + y3 - 4xz +f(y)(a) If possible, fi nd a function f (y) for which the laplacianof F is zero. If you do indeed solve part (a), can your fi nalfunction F serve as (b) a velocity potential or (c) a streamfunction?
4. Consider steady flow of water through an axisymmetric garden hose nozzle (see Fig). Along the center line of the nozzle, the water speed increases from uentrance to Uexit as sketched. Measurements reveal that the centerline water speed increases parabolically through the nozzle. Write an equation for centerline speed u(x), based on the parameters given here, from x=0 to x=L. Dentrance Dexit Hentrance Hexit u(x) x=L
Find the vorticity of the fluid motion for the given velocity com- ponents. KINEMATICS OF FLUIDS (a) u A(x + y), v = - A(x + y) (b) u = 2Axz, (c) u Ay²+ By + C, v = A(c² + x² - z²) 1)=0
Suppose that it is desired to estimate volume fl ow Q in apipe by measuring the axial velocity u ( r ) at specifi c points.For cost reasons only three measuring points are to be used.What are the best radii selections for these three points?
Consider steady, incompressible, two-dimensional flow due to a line source at the origin. Fluid is created at the origin and spreads out radially in all directions in the xy-plane. The net volume flow rate of created fluid per unit width is V·/L (into the page of Fig), where L is the width of the line source into the page in Fig Since mass must be conserved everywhere except at the origin (a singular point), the volume flow rate per unit width through a circle of any radius r must also be V·/L. If we (arbitrarily) specify stream function ? to be zero along the positive x-axis (? = 0), what is the value of ? along the positive y-axis (? = 90°)? What is the value of ? along the negative x-axis (? = 180°)?
Q.5 A plate 1 mm distance from a fixed plate, is moving at 500 mm/s by a force induces a 2 shear stress of 0.3 kg(f)/m. The kinematic viscosity of the fluid (mass density 1000 kg/ 3. m) flowing between two plates (in Stokes) is
P1.20 A baseball, with m = 145 g, is thrown directly upward from the initial position z = 0 and Vo = 45 m/s. The air drag on the ball is CV², as in Prob. 1.19, where C~ 0.0013 N: s*/m". Set up a differential equation for the ball motion, and solve for the instantaneous velocity V(t) and position z(1). Find the maximum height zmax reached by the ball, and compare your results with the classical case of zero air drag.
- Assume the input power to a pump P (M L T-¹) is depend on Q- Flowrate (L3 T-¹), H-pump head (L), p- fluid density (ML-³) Create a relation by dimensional analysis between the power and other variables by Buckingham Theorem. Assume the input power to a pump P (M L T-¹) is depend on Q- Flowrate (L3 T-¹), H-pump head (L), p- fluid density (ML-³) Create a relation by dimensional analysis between the power and other variables by Rayleigh Method.
Consider steady flow of water through an axisymmetric garden hose nozzle. The axial component of velocity increases linearly from uz, entrance to uz, exit as sketched. Between z = 0 and z = L, the axial velocity component is given by uz = uz,entrance + [(uz,exit − uz,entrance)/L]z. Generate an expression for the radial velocity component ur between z = 0 and z = L. You may ignore frictional effects on the walls.
U L CD Fig.1. Airflow on a cylinder U U U/2 L/2 L/2 1. When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. (a) If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. (b) Rewrite your result in the form of a dimensionless drag coefficient based on body length F pU²bL