Fig.1. Airflow on a cylinder U/2 F pU²bL 1/2 [4/2 1. When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. (a) If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. (b) Rewrite your result in the form of a dimensionless drag coefficient based on body length CD

Fig.1. Airflow on a cylinder U/2 F pU²bL 1/2 [4/2 1. When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. (a) If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. (b) Rewrite your result in the form of a dimensionless drag coefficient based on body length CD

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. The Stokes-Oseen formula for drag force Fon a sphere of diameter D in a fluid stream of low velocity V, density p, and viscosity u is: 9T F = 3TuDV + 16PD? Is this formula dimensionally homogenous? 2. The efficiency n of a pump is defined as the (dimensionless) ratio of the power required to drive a pump: QAp input power Where Q is the volume rate of flow and Ap is the pressure rise produced by the pump. Suppose that a certain pump develops a pressure of Ibf/in? (1ft = 12 in) when its flow rate is 40 L/s (1L =0.001 m). If the input power is 16hp (1hp = 760 W), what is the efficiency?
When a uniform stream flows past an immersed thick cylinder, a broad low-velocity wake is created downstream, idealized as a V shape in Fig. 1. Pressures p1 and p2 are approximately equal. (a) If the flow is two-dimensional and incompressible, with width b into the paper, derive a formula for the drag force F on the cylinder. (b) 1. Rewrite your result in the form of a dimensionless drag coefficient based on body F length Cp pU²bL U = L Fig.1. Airflow on a cylinder U U U/2 L/2 L/2
1. In Class, we used a small differential volume to derive the expression for momentum thickness. Here, use a control volume approach, as shown in the figure, to derive the definition of momentum thickness, 0, for flow over a flat plate. zero shear stress, constant pressure, no through flow h> 8 no slip, ,#0
1- Reynolds number is a dimensionless number represent .....to .. 2- The velocity profile of the flow between two parallel plates is linear if the pressure gradient equal and parabolic if the pressure gradient has a .... 3- In the sink and source flow the potential function is represented as.. ...... and the stream function is represented as **** 4- In the laminar boundary layer, the .............. is the dominant reason for the loss while in turbulent boundary layer the is dominant. 5- For inviscid flow, there are no shear stresses the only forces acting on a fluid element are ....... and. *****
Q3) In some wind tunnels the test section is perforated to suck out fluid and provide a thin viscous boundary layer. The test section wall in Fig.3 contains 12064 holes of 5 mm diameter. The suction velocity through each hole is Vs = 8 m/s, and the test section entrance velocity is V₁ = 35 m/s. Assume incompressible steady flow of air at 20°C, compute, Vo, V₂ and Vf in m/s. Test section D₁ = 0.8 m Uniform suction D₁= 2.2 m Do = 2.5 m V₂ -L=4 m Fig.3 L Vo-
A horizontal circular jet of air (pair plate as shown below. The air jet has a velocity V; = 60 m/s and the air jet has a diameter Dj = 40 mm. An anchoring force FA is holding the plate in its stationary position. This entire system is open to the atmosphere. 1.23 kg/m³) strikes a stationary flat Gravity is into / out of the page ... gravity will not be important here! The air velocity magnitude remains constant ( |Vi| = |V2| = |V3| ) as the air flows across the plate surface (this means there are no shear stress effects). Hint align your coordinate system with V3, V2, and FA. ... V2 D : = 40 mm V; = 40 m/s 30° V3 FA (3.a) What is the magnitude [ N ] of the anchoring force FA? (3.b) What fraction [ % ] of the total mass of air leaves at V2? Now we will change the problem a little. Allow the plate to move to the right with a constant speed of 18 m/s. You should realize that this will mean that the anchoring force is reduced from the answer you found in (4.a). Please place your observer…
[1] Consider steady flow of air through the diffuser portion of a wind tunnel. Along the centerline of the diffuser, the air speed decreases from uentrance to ut as sketched. Measurements reveal that the centerline air speed decreases parabolically through the diffuser. Write an equation for centerline speed u(x), based on the parameters given here, Dee x=0 to x=L.
Pipelines are cleaned by pushing through them a closefitting cylinder called a pig . The name comes from thesquealing noise it makes sliding along. Reference 50describes a new nontoxic pig, driven by compressed air, forcleaning cosmetic and beverage pipes. Suppose the pigdiameter is 5-15/16 in and its length 26 in. It cleans a6-in-diameter pipe at a speed of 1.2 m/s. If the clearance isfi lled with glycerin at 20 8 C, what pressure difference, inpascals, is needed to drive the pig? Assume a linear velocityprofi le in the oil and neglect air drag.
QUESTION: (ii) Use Buckingham's theorem to obtain in dimensionless form an expression for the force acting on a smooth sphere placed in an incompressible viscous flow filed .
Consider laminar flow through a long section of pipe, as in Fig. For laminar flow it turns out that wall roughness is not a relevant parameter unless ? is very large. The volume flow rate V· through the pipe is a function of pipe diameter D, fluid viscosity ? , and axial pressure gradient dP/dx. If pipe diameter is doubled, all else being equal, by what factor will volume flow rate increase? Use dimensional analysis.
A 1:7 scale model simulates the operation of alarge turbine that is to generate 200 kW with a flowrate of 1.5 m3/s.What flow rate should be used inthe model, and what power output is expected?(a) Water at the same temperature is used in bothmodel and prototype.(b) The model water is at 25°C and the prototypewater is at 10°C.
Suppose that it is desired to estimate volume fl ow Q in apipe by measuring the axial velocity u ( r ) at specifi c points.For cost reasons only three measuring points are to be used.What are the best radii selections for these three points?