Find the value of parallel capacitance needed to correct a load of 120 kVAR at 0.75 lagging pf to unitypf. Assume that the load is supplied by a 220-V (rms), 50-Hz line.a. 1.56 mFb. 0.47 mFC. 5.32 mFd. 7.89 mF When connected to a 220V (ms), 50 Hz power line, a load absorbs 4kW at a lagging power factor of0.65. Thus, the value of power reactance correction needed to raise the pf to 0.9 isa. 3.410 KVARb. 2.7340 KVAR4.6768 KVARd. 1.9372 KVAR

Answered: Image /qna-images/answer/8f0c13fb-ec09-4584-94ea-ed4526bda250.jpg

Find the value of parallel capacitance needed to correct a load of 120 KVAR at 0.75 lagging pf to unity pf. Assume that the load is supplied by a 220-V (rms), 50-Hz line. a. 1.56 mF b. 0.47 mF C. 5.32 mF d. 7.89 mF

Find the value of parallel capacitance needed to correct a load of 120 KVAR at 0.75 lagging pf to unity pf. Assume that the load is supplied by a 220-V (rms), 50-Hz line. a. 1.56 mF b. 0.47 mF C. 5.32 mF d. 7.89 mF

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the following circuit, find the magnitude of the current i, (mA,rms). 2002 3000 j100N I2 j1000 Sj200Q -j3000 j6000 100 Vrms ll ll +
2. A voltage applied to a load is V=208 4 20°V and current through load is I=10 a–10° A. Find the following [SO 1] o complex power consumed by load o Is the load inductive or capacitive? o the power factor of the load o the reactive power consumed or generated by the load. o Does the load consume or supply reactive power?
Two relays each with 20-ohm resistance and 0.16-henry inductance are connected in series. What is the equivalent impedance?a. 20 + j102.2 ohms c. 20 + j95.32 ohmsb. 20 + j120.63 ohms d. 10 + j25.32 ohms
RMS Value of sinusoidal current is given by O a. Im//2 b. I,x2 Ос. c. ImX/2 O d. I/2 m
Load 1 Load 2 24 kW 40 kW pf = 0.8 lagging pf = 0.95 lagging %3D A 240-Vrms, 60 Hz source supplies two loads as shown above. Find the capacitance of a capacitor connected in parallel that will raise the power factor to unity. O 3.14 millifarad O 4.45 millifarad O 1.43 millifarad 5.74 millifarad
Two loads are connected in parallel to a 1000 v(rms) 60Hz source. One of the loads has an average power of 500 kW and a forward power factor of 0.9. Since the other load absorbs 400kw and 600kvar power a) Draw the equivalent circuit of the system b) Find the common power factor of the system c) Find the value of the capacitor to be connected parallel to the loads so that the power factor is 0.95 back d) Find and compare the magnitude of the current drawn from the .source for the situations before and after the capacitor is connected not: Please solve this question in detail, in a way that I can understand
A load is supplied by a 230 V, 50 Hz source. The active power P and the reactive power Q consumed by the load are such that 1 kW SPS2 kW and 1 KVAR SQS2 KVAR. A capacitor connected across the load for power factor correction generates 1 KVAR reactive power. The worst case power factor after power factor connection is Options: 1. 0.447 lag 2. 0.707 lag 3. 0.894 lag 4.1
Three identical Y-connected loads, each having a resistance of 20 22 in parallel with an inductor, are connected to a three phase supply of 400 V and 50 Hz frequency. The power absorb by the load is 8 kW and power factor at the load is 0.9919. (i) Determine the current that flows through the inductor. Please state the assumptions used to solve the question. Calculate load inductance in Henry (H).
find The average power delivered to * .the circuit الحل بطريقة الممانعات وشكرا
For a source which has load has the following characteristics: • Vrms = 125 20° V • P= 400 W • pf = 0.925 lagging What is the rms current and reactive power?
2. Three series loads are drawing 20A ms current through a 60HZ source. Load 1 is an 400W, 0.8 lagging induction motor. Load 2 is a 500VA, 0.6 lagging power factor and load 3 is a 2 ohm incandescent bulb. a) What is the total VA of the combined load? b) What is the overall PF of the combined load? c) What RMS voltage is the combined load operating? d) What capacitor VAR must be installed in parallel to the combine load to improve its overall PF to unity? e) What is its approximate capacitance in microfarad?
Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. Time remaining: 00:07:30 Electrical Engineering Consider the situation shown in (Figure 1). A 1000-V-rms source delivers power to a load. The load consumes 140 kW with a power factor of 55 percent lagging. 1- Find the phasor II, assuming that the capacitor is not connected to the circuit. Enter your answer using polar notation. Express argument in degrees. 2-Find the value of the capacitance that must be connected in parallel with the load to achieve a power factor of 100 percent. Express your answer to three significant figures and include the appropriate units. 3-Usually, power-systems engineers rate capacitances used for power-factor correction in terms of their reactive power rating. What is the rating of this capacitance in kVAR? Express your answer using three significant figures. 4-Assuming that this…