Find the length of cantilever beam to carry the loads shown in the figure below: D.L= Self weight, P.L.L= 50kN, that the beam remain uncracked, use the following data: effective top cover = 60mm width of the beam = 350mm, height of the beam =650mm f24MPa, f= 400MPa. C.C h=650mm umfram 4032mm Xb-350mmX self-weight 4m P.L.L 5kN X

Find the length of cantilever beam to carry the loads shown in the figure below: D.L= Self weight, P.L.L= 50kN, that the beam remain uncracked, use the following data: effective top cover = 60mm width of the beam = 350mm, height of the beam =650mm f24MPa, f= 400MPa. C.C h=650mm umfram 4032mm Xb-350mmX self-weight 4m P.L.L 5kN X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam and its loading is shown where F1= 1000 N/m. F1 1600 N/m A B 6 m Determine the magnitude and location of the resultant of the distributed load. (You must provide an answer before moving to the next part.) The magnitude of the resultant of the distributed load is The location of the resultant of the distributed load is m. (Click to select)
Asap
Two identical 10 mm diameter A36 steel wires support the rigid beam shown. Determine the maximum load P that can be applied if a Factor of Safety of 2.0 is required. See the text Appendix for any material properties that are needed. E 4 m A -3 m 2 m
Question 16 A W10x30, 2.9 m long, A36 steel is used as a column with fixed ends to support a service dead load of 154 kN. Calculate the maximum service live load the column can sustain using LRFD. Use theoretical value of k. Write your answer rounded to the nearest whole number in kN. A = 5,703 mm2 rx = 111.25 mm ry = 34.80 mm
.
Determine the design strength of a T- Beam given the following data: bf = 700 mm bw = 300 mm hf = 100 mm d = 500 mm fc' = 21 MPa fy = 414 MPa As: 5- 20 mm dia.
The dimensions of a T-section are shown in the figure. 10 mm 10 mm For the depth of plastic neutral axis from the top of the T-section to be 9.583 mm, the flange width 'b must be (in mm). 110 mm
A lightly welded steel beam shown in Figure 5 is continuously supported along its length. A downward concentrated load of 4P acts at Point C, and two downward concentrated loads P act at Points A and E. The beam with full lateral restraint is bent about its major principal x-axis. Determine the followings: a. Section type based on section slenderness; b. Effective section modulus; c. The maximum design value of P. A k B fu 6 m d tw bf 6 m tf 4P d bf tw tf = - = fyf= fyw 6 m D um * 550 mm 206 mm 6 mm 10 mm 320 MPa = 340 MPa Zx=1362985 mm³ Sx 1533750 mm³ Figure 5 Steel beam under design loads. 6 m P E
Steel structure-Civil Engineering please answer the 5th question .
For the hollow beam. Calculate the design. capacity, As = 2040mm ² Fy = 420 Mpa,Fc=25Mpa,Asmin check is not required
Please answer the problem below, using NSCP 2010/2015,Using 4 decimal. 16-28mm diameter bar
Plase answer questions from (d)