The compound bar ABCD has a uniform cross-sectional area of 0.36 in2.Determine the change in length (in inches) of the bar if an axial force P = 4084 lbis applied.The moduli of elasticity are 29016 ksi for steel and 10059 ksifor aluminum. Round off the final answer to four decimal places.

The compound bar ABCD has a uniform cross-sectional area of 0.36 in2.Determine the change in length (in inches) of the bar if an axial force P = 4084 lbis applied.The moduli of elasticity are 29016 ksi for steel and 10059 ksifor aluminum. Round off the final answer to four decimal places.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter6: Introduction To Mechanical Properties

Section: Chapter Questions

Problem 8ETSQ

See similar textbooks

Related questions

Q: Problem II. Solve the problem using Conjugate Beam Method. The beam shown has a constant El and is…

Q: Q.2.A.The closed tank in figure is at (20°c) (specific weight of air =0.0118 kN/m³). If the pressure…

Q: An 800-g block is attached to a horizontal spring and executes simple harmonic motion with a period…

A: Using the definitions of time period and total energy of a simple harmonic oscillator the value of…

Q: did the value 0.00135 come from?

A: The value .00135 is the strain in steel. And the value .003 is the allowable strain in concrete.

Q: w = 3 rad/s 26 in. 4 ft/s

Q: نقطة واحدة Igneous rocks are the must propagation in the word True O False

A: True.

Q: A Qy Q₁) Find the cracking Moment for the beam section Shown in figure below. if fr = 20 мра, Es =…

A: Cracking moment The Cracking Moment, also known as Mcr, is the point at which concrete begins to…

Q: In a standard proctor test, 3.2 kg of moist soil was filling the mould of volume 944 cc after…

A: given- Standard proctor test-bulk weight of the soil=3.2 kgweight of the sample to be oven dried=40…

Q: Q.1 The velocity distribution in a turbulent boundary layer is given by 1/7 What is the displacement…

Q: B W 5.4 m

Q: Q1:-Answer the following statements with (True) or (False), ( 4) When the coefficient of contraction…

A: Fluid mechanics : Fluid mechanics, the field of science that studies fluids (liquids and gases) in…

Q: be (in inches) if the volume of the box is to be maximized?

Q: A uniformly distributed load on beam ABC in Figure P6.9 causes it to sag. To counteract this sag, a…

A: Determine the forces in the cable and the post and determine the reactions at A and C.

Q: Q1: For Figure (1), determine both the x-y and the n-t components of force F. 41.475 re (2)…

Q: Q7/ Lake A losses feed Lake B. The distance between them is 3.5 km. Lake A has a water level of…

Q: Determine the area enclosed by y = 3x - 2, the x-axis and ordinates x=2 and x=4

A: y= 3*2-2= 4 y= 3*4-2= 10 x= 2 x=4 Area enclosed by the graph = (4-2)*(10-4)= 12 sq units

Q: ncentration of 100 mg/L using a settling column was carried out in a oratory. The results of the…

A: Given - L = 45 M B= 12 m Q =8.1 MLD =8.1×106 LD Q =8.1×103 m3/sec24×60×60 Q=0.09375…

Q: Design a rectangular reinforced concrete beam for a simple span of 32 ft. Uniform service loads are…

Q: 18. If a close coiled helical spring absorbs 30 Nmm Hoof energy while extending by 5mm, its…

A: Given data: Extending spring on coiled helical = 5 mm Absorb energy by close coiled helical spring =…

Q: For the given shear diagram, draw the load and moment diagram. 40 in. 0 -6.67 lb -207 lb 73.3 lb 40…

Q: 1. Analyze the frame. 1m 2W(kN/m) 3m 1.5W(kN/m) 2m 3110 60°

A: Given data:

Q: A stream conveying a flood peak of 40 m3/s (velocity 1.45 m/s and depth 0.9 m) is divided into 3.1 m…

A: step 1-

Q: Member BD of the pin-connected frame has a rectangular cross section 200 mm wide by 400 mm deep.…

A: Determine the maximum normal stress in this member.

Q: Draw the shear and moment curves for the beam shown. Reaction at support B is given. Then; a)…

Q: The common tangent BC of a reverse curve is 281 m and has an azimuth of 311 degrees . AB is tangent…

A: Given, AB= 320m BC=281m CD=301m To find :- A)radius of the first curve B)length of the curve from…

Q: Q.3: The working stresses for the manufactured wood beam are 10 MPa in bending and 1.4 MPa in shear.…

Q: There is a horizontal external force P = 4kN applied on point B. The axial rigidity EA of all truss…

A: P = 4KN

Q: ) Constructed the plan (the activity by arrows) Method, find the construction time for this project…

A: 17 weeks ADGH

Q: 6) The simply supported beam with given cross-section supports the loads as shown. Determine the…

Q: 4) A simply supported box beam is constructed using 4 pieces of 50 x 200 glued together supports the…

A: Size of pieces = 50 × 200 mm

Q: Column W200 x 71 shown in Figure 1 has the length of 4m has load of P = 150kN acting at e = 50 mm.…

Q: Q.1 The velocity distribution in a turbulent boundary layer is given by 1/7 What is the displacement…

Q: Required to prepare the action plan for the events by (A.O.N). method, show in table below and…

Q: 4. An engineer bought an equipment for P500,000. Other expenses including installations amounted to…

Q: 100 N (a) (b) W = 200 N 0.3 0.2 W = 40 N fls Mk - Mg = 0.9 M₁ = 0.6

A: Given data:- Part A:- Part B:-

Q: Compute the moment about point A. Use F1-300 lb, F2-250 lb and F3-200 lb. Show all work on your…

A: Newton's third law states that when two bodies interact, they apply forces to one another that are…

Q: Q.4.A..A (3m) high, (5m) wide rectangular gate is hinged at the top edge at (A), and is restrained…

Q: 5. A plate of 6inx 1 in with steel grade A36 (fy-36ksi and Fu-58 ksi) is used as tension member with…

Q: The height of the capillary rise of water increases as particle diameter increases True O

A: Ans: False Explanation: In the soil, usually, as the grain size decreases the size of the voids…

Q: A -3 m B W 5.4 m YC 4,5 m- -www :

Q: ntaining 90% of carbon and 8% of hydrogen give the following result in the bomb calorimeter…

A: Given:- liquid weight=0.98gm content of carbon=90% content of hydrogen=8% calorimeter value of…

Q: A sewage treatment plant is designed to treat wastewater from a population of 20,000 PE. A treatment…

A: Let average sewage flow per person per day = 180L/day/person

Q: Figure 1 shows the elastically deformed shape AB'C'D' of a thin plate subjected to plane stress…

A: At point O which is half of the undeformed square. Therefore the total angular displacement of the…

Q: A flood of certain magnitude has a return period of 25 years. The probability of exceedance is ?

A: given- Return period T=25 yearsIt is needed to find the probability of exceedance.

Q: Question Number (1) Wastewater Engineering Civil Engineering Draw a complete schematic diagram…

Q: Q3/ A vertical curve below has a lower point (A) which exists at station (55+50) with elevation…

Q: A W12×26 tensile member with no holes

Q: 1. A sewage treatment plant is designed to treat wastewater from a population of 20,000 PE. A…

Q: 2) Consider a cylindrical vessel that is subjected to both an internal pressure p and an applied…

Q: A- Extended aeration B- Conventional C-High rate aeration D-Step feed aeration **Good Luck**

A: Answer - Extended Aereation Extended aeration systems provide long residence times with low F / M…

Concept explainers

Material Properties

Construction in civil engineering demands high strength, durability, and longevity. These targets can be achieved by better design and analysis, along with the correct choice of materials. Different materials have different properties and hence, they respond and performs differently under the various condition of external loadings. It is therefore a critical task of an engineer to select the right material based on the property that the material is supposed to function in real-time. When speaking about the property, there are different categories of material properties like chemical property, physical property, mechanical property, electrical property, magnetic property, thermal property, etc. These material properties form the basis of material selection in various applications.

Question

100%

please help! upvote will be given. NO LONG EXPLANATION NEEDED

STRENGTH OF MATERIALS

Round off the final answer to four decimal places.

P-
A
18 in.
Steel
18 in.
Steel
-Aluminum
6 in.
BC
P

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

This is Structural theory. Formula: For #1 : r-3-c #2: r+m-2j #3: r+m-2j
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 34-in.-long bronze [E = 14300 ksi, a = 8.4 x 10-6/°F] bar with a cross-sectional area of 1.75 in.². Bar (2) is a 42-in.-long aluminum alloy [E = 10200 ksi, a = 11.9 × 10-6/°F] bar with a cross-sectional area of 2.00 in.². Both bars are unstressed before the load P is applied. Assume L₁=34 in., L₂=42 in., a=38 in., b=52 in., and c=16 in. If a concentrated load of P = 33 kips is applied to the rigid bar at D and the temperature is decreased by 85°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) A B a (1) L₁ b C L2 D
CLO 2: It is the combined stress at the top fiber of a beam subjected to axial compression and positive bending. O +P/A - Mc/l O P/A - Mc/l O +P/A + Mc/I O -P/A + Mc/I Next
CLO 2: It is the combined stress at the top fiber of a beam subjected to axial compression and positive bending. O -P/A + Mc/l +P/A + Mc/l +P/A - Mc/I O -P/A - Mc//
It is a system that is composed of combination of interconnected structural elements and is used to support various loadings. O Load analysis system O Truss system O Statically determinate system O Structural system
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 30-in.-long bronze [E = 15900 ksi a = 9.4x 10-6/°F] bar with a cross-sectional area of 1.00 in.?. Bar (2) is a 48-in-long aluminum alloy [E = 9200 ksi, a = 12.6 x 10-6/°F] bar with a cross-sectional area of 2.50 in.?. Both bars are unstressed before the load Pis applied. Assume L4=30 in., L2=48 in., a-32 in., b=44 in., and c=14 in. If a concentrated load of P = 29 kips is applied to the rigid bar at Dand the temperature is decreased by 120°F, determine: (a) the normal stresses in bars (1) and (2). (b) the normal strains in bars (1) and (2). (c) the deflection of the rigid bar at point D. (2) L2 A B D L1 (1) b
Determine the yield strength sy and the ultimate strength su of the A36 steel
1. To gain structural strength, the dimensions of aluminum are increased. T or F
List the specifying organization for the following types of steel:a. Cold-formed steelb. Hot-rolled steel
A 750-MM SHAFT IS COMPOSED OF STEEL AND ALUMINUM PARTS. DETERMINE THE CENTROIDAL Y (IN MM) OF THE SHAFT IF THE DENSITY OF STEEL p, = 7800 KG/M AND THE DENSITY OF ALUMINUM PA = 9.75 x 102 LB/IN. HINT: USE INTEGRATION IN OBTAINING THE FORMULA FOR THE VOLUME AND CENTROID OF A FRUSTUM OF A CONC.. STEEL ALUMINUM END I 20 mm 40 mm (RAD) END 2 60 mm 130 mm (DIA)
Find the largest value of P that will not exceed the following stresses: 180 MPa in steel, 160 MPa in bronze and 90 MPa in aluminum.
Rigid bar ABCD is supported by a pin connection at A and by two axial bars (1) and (2). Bar (1) is a 24-in.-long bronze [E = 16100 ksi] bar with a cross-sectional area of 1.18 in.2. Bar (2) is a 40-in.-long aluminum alloy [E = 9400 ksi] bar with a cross-sectional area of 2.03 in.2. Assume L1=24 in., L2=40 in., a=31 in., b=41 in., and c=12 in. Both bars are unstressed before the load P is applied. If a concentrated load of P = 36 kips is applied to the rigid bar at D, determine:(a) the normal stresses σ1σ1, σ2σ2 in bars (1) and (2).(b) the downward deflection vD of point D on the rigid bar.