Find the expression for the output function, F. Do not simplify. Vdd- B C B bar B bar A 0 A bar A bar F

Q: The hexadecimal equivalent of a binary 0010111101111110 is O a. 2F6E O b. 77F2 O c. 2F7E d. 4EEE

A: Given, The binary number is 0010111101111110.

Q: DFF circuit that adds the one-bit numbers a and b in series. Design according to the Mealy model…

A: Finite state Machine- In a combinational circuit, the output only depends on the value of input as…

Q: Q2: A PAM signal f(t) = 2cos n 4t is sampled at rate of 16 Hz using 8 levels quantization . Indicate…

A: f(t)=2cos π4t fs=16Hz

Q: LOGIC CIRCUITS & DESIGN I. DESIGN THE CIRCUITS OF SEVEN SEGMENT LED’S 0-7 USING THREE VARIABLE…

A: For the following questions we have to find the the truth table, k map,circuit diagram

Q: Problem 6: For the following state table: Next State Output Present State x = 0 x = 1 x = 0 x = 1 f…

A: We are authorized to answer one question at a time since you have not mentioned which question you…

Q: What are the machine cycles and the total execution time needed by the 8085 µp to execute LHLD 2066H…

A:

Q: (ii) What are the bit weights for LSB and MSB in an 8-bits DAC system? (iii) Consider the R-2R…

A: In the given questions we need to discuss about the DAC.

Q: Q2: Design 4-bit Parallel-in to Parallel-out (PIPO) using RS-F/F. Draw the parallel output waveform…

A: The diagram for 4-bit Parallel-in to Parallel-out (PIPO) using RS flip-flop is shown below:

Q: 7. For the state diagram shown, derive the state/output table. A B 21 z2 11 21 z2 = 10 X.Y E 21 22…

A: A state-diagram is a visual representation of a series of circuits. It clearly shows the transition…

Q: a) Fill in the table below for 4-bit A/D converter if Va = 13V with a reference voltage of 15V. Show…

A: According to the question, for a 4-bit SAR ADC the reference voltage is 15 V and the input voltage…

Q: Following is the segment of a 8085 assembly language program LXI SP, EFFF H CALL 3000 H 3000 H: LXI…

A: Solution !!

Q: W, Vcc 74151A Do D D2 D3 D4 Ds Do f(W.X,Y,Z) Y D7 CBA XYZ Selection code ww

A:

Q: 1- circuit in the figure, if Vcesat=0V, Vcc as Logic 1, OV as Logic 0 is applied for the Q1…

A:

Q: The output from a sensor ranges from a minimum of 10 mV to a maximum of 200 mV as the measurand…

A: An instrumentation amplifier allows an engineer to adjust the gain of an amplifier circuit without…

Q: 2. A thermal couple measures a temperature range between 0°C to 500°C. It is required that the…

A: According to question: Resolution = 0.50C

Q: Which output is shown for (Q?) ? 10 FFO FF1 FF2 FF3 01 (a) 10 11 12 13 14 15 16 Clock-Input Q ?

A: The sequential circuit given represents the four bit asynchronous up counter where four JK flip…

Q: 1. Five channels, each with a 100-kHz bandwidth, are to be multiplexed together. What is the minimum…

A: As per Bartleby regulation I should answer the first question of a post where multiple questions…

Q: (c) Express F as sum of minterm's ,F(X,Y)-E(...) in the following circuit NANDE SON 1 * (d) What…

A: (c).  If A and B are the inputs to an Ex-OR (XOR) gate, then the output of the XOR gate can be…

Q: The input to ADC, 10-bit, with a 2.5-V reference is 1.45 V. Suppose the output was found to be 1B4…

A: Input to ADC, 10-bit, with a 2.5-V reference is 1.45 V. Output was found to be 1B4 in hexadecimal.…

Q: ADC resolution A 4-bit ADC has a reference voltage of 5.000 v. a) What is its voltage resolution? b)…

A: The analog-to-digital converter(ADC) is used to convert the analog input into digital output and the…

Q: For the circuit given in the Figure (1) Determine the final output expression (Y) and find the truth…

A: Y=B+C+A¯+B¯Y=B+C+A.B¯Y=B+C+A

Q: ; An experimenter uses a 10-bit A/D having a range from -5 [V] to +5 [V] to digitize a 35.0 [mV]…

A:

Q: 12.13 A 74178 shift register is described by the given table. All state changes occur on the 1-0…

A:

Q: 1. The Analog signal given below is sampled at 1KHz rate and quantized with a 4 bit quantizer. 2.00…

A: Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Problem 16. We are comparing to COTS ADCs (Commercial Off-The-Shelf Analog to Digital Converters).…

A: For unit B the ENOB is 8.8 bits and unit B is a 10-bit ADC.We need to calculate the SINAD for unit…

Q: - An experimenter uses a 10-bit A/D having a range from -5 [V] to +5 [V] to digitize a 35.0 [mV]…

A:

Q: n . when input change, may affect the output Morre model Mealy model O

A:

Q: (b) Figure Q2(b) shows a logic circuit that is constructed by using two multiplexers, MUX1 and MUX2.…

A:

Q: 1 Please design a comparator which can compare two 1-bit number and out corresponding result (please…

A: The digital circuits can be combinational as well as sequential circuits. The combinational circuits…

Q: Y, DQ Q Yo yo Q a

A:

Q: A 14-bit ADC with VFS = 5.12 V has an output code of 10101110110010. What is the possible range of…

A: Concept: The voltage between two points is a short name of the electrical force that would drive an…

Q: In a 8 bit DAC using binary weighted resistors, if the MSB resistors is 30KO, the LSB resistor ΚΩ O…

A: We need to tell about resistance value of LSB in DAC .

Q: Q. ) What are the frequencies F1, F2, F3 10MHZ is applied? after each stage if an input clock of…

A: Counter is a  sequential circuit made up of flip flop which are connected to count the pulses . It…

Q: d. When converting an analog signal to digital form, the resolution of the conversion is an…

A: The given problem is from Analog to digital converter (ADC). The detailed solution is given in the…

Q: Q1/ Design 4-bit D/A Binary-Weighted with a Verf=14 V where the minimum resistance you can use in…

A: The solution can be achieved as follows.

Q: Design a-full subtractor with two multiplexers (MUXS) Say2 Σ(... ) , C(x.y.2) = E(...). Connect the…

A:

Q: Q2: A PAM signal f(t) = 2cos n 4t is sampled at rate of 16 Hz using 8 – levels quantization.…

A: f(t) =2 cos π 4 tfs =16 HZl= 82n=lNo of bits per word n ,= 3

Q: 1. A combinational circuit adds either a 1 or 2 to a 4-bit binary number A. Assume that the inputs…

A: The truth table is drawn as: C A3 A2 A1 A0 X3 X2 X1 X0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 1 0…

Q: X QO K Q Q1 K Q CK

A: State diagram

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.