Example 1. For the half-wave rectifier shown below, determine the following: (a) Secondary voltage of the transformer if Vp = 220 Vrms (b) Sketch of the rectified signal and peak voltage of the rectified signal, Vm (c) Reading of the DC voltmeter, Vdc (d) Reading of the DC ammeter connected in series with the load, Idc (e) Percent ripple, %r (f) Diode's PIV Si 500:50 + Vp RI VL 2K2

Example 1. For the half-wave rectifier shown below, determine the following: (a) Secondary voltage of the transformer if Vp = 220 Vrms (b) Sketch of the rectified signal and peak voltage of the rectified signal, Vm (c) Reading of the DC voltmeter, Vdc (d) Reading of the DC ammeter connected in series with the load, Idc (e) Percent ripple, %r (f) Diode's PIV Si 500:50 + Vp RI VL 2K2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In a centre-tapped full wave rectifier having a load resistance resistance equals 3 2. The turn's ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS ), 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency. 750 52 diode forward bias
A three phase full wave rectifier is shown below along with the peak input phase voltage Vm=169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is Vpc=280.7V and. The RMS transformer secondary current is equal to 81.72A, the output RMS voltage is equal to VRMS=280.93V and the output resistance is equal to 2.8070. The TUF would be equal to: Secondary a平a字a辛 R 太D。太D。太D. Select one: 0.875 Ob. 0.955 O C. 0.551 O d. 0.432 Compared with power transistors, thyristors have the following characteristic
In the circuit in the figure, an AC voltmeter will be made with full wave rectifier circuit structure. R = 50ohm and diodesResistance values in the direction of transmission are Rd = 100ohm. Inside of the DC ammeter to be used as indicatorthe resistance is very, very small. The AC mark to be measured is Vs = 100 Sinwt Volts.a- Draw the shape of the current passing through the DC Ammeter and calculate its maximum value.b- Find the average value of the current passing through the DC Ammeter.c- Analyze the voltage seen at the ends of diode D1 for both alternans.d- Find the Rms value of the voltage seen at the ends of the diode D1.
Full Wave Rectifier Circuit The circuit of the full-wave rectifier can be constructed in two ways. The first method uses a centre tapped transformer and two diodes. This arrangement is known as a centre tapped full-wave rectifier. The second method uses a standard transformer with four diodes arranged as a bridge. This is known as a bridge rectifier. Advantages of Full Wave Rectifier The rectification efficiency of full wave rectifiers is double that of half wave rectifiers. The efficiency of half wave rectifiers is 40.6% while the rectification efficiency of full wave rectifiers is 81.2%. The ripple factor in full wave rectifiers is low hence a simple filter is required. The value of ripple factor in full wave rectifier is 0.482 while in half wave rectifier it is about 1.21. The output voltage and the output power obtained in full wave rectifiers are higher than that obtained using half wave rectifiers. Question: What is the main disadvantage of a conventional full-wave…
the three phase half wave uncontrolled rectifier is operated from 500v,50Hz supply at secondary side and the load resistance is 25 ohms. if the source inductance is negligible, determine a) rectification efficiency b) form factor c) ripple factor d) transformer utilization factor e) peak inverse voltage of each diode
The peak output voltage for the bridge rectifier in the figure is_______Volts. Assuming ideal diodes, the PIV rating required for the diodes is ______Volts. The transformer is specified to have 12 Vrms secondary voltage for the standard 110 V across the primary.
Q5. For the following center tapped transformer, show the waveform across each half of the secondary winding and across Ri, when a 100 V peak sine wave is applied to the primarywinding. What is the PIV rating must the diode have? (Use constant voltage drop model for the Silicon diode) IN4001 Ry OV 10k) D IN4001
An ideal single-phase full wave rectifier circuit has a non-inductive resistanceload, negligible tube drops and no transformer losses. What is therectification or conversion efficiency in percent?
The main advantage of a bridge rectifier using tha same input transformer as a full-ave rectifier is that _______________. a) İt will double the output voltage. b) less current is required fort he diodes to conduct. c) the ripple frequency is twice that of the full wave rectifier. d) the ripple frequency is on-half that of the full wave rectifier.
A load is connected in the Full Bridge rectifier circuit (Four Diodes). Usedtransformer primary voltage value is 220 V (rms). The transformer winding ratio is 1:10.Using the 0.7 V model of the diode,Load Rating: 7 K Ohmsa) How many % of conduction does each diode branch stay on?b) Find the average values of the load voltage.c) Find the average values of the load current.d) Find the effective value of the load voltage.e) Find the effective value of the load current.
In a centre-tapped full wave rectifier, the diode having a forward resistance of 3 ohm and the load resistance equals to 750 ohm. The turns ratio of the centre tapped transformer is 20:1. The primary winding of transformer is fed from a supply voltage of 220 V (RMS) 50 Hz. Determine a) Average and RMS value of load currents b) DC voltage and DC power output c) AC input power d) ripple factor and e) rectifier efficiency.
A half-wave rectifier is to provide an averagevoltage of 50 V at its output.a. Draw a schematic diagram of the circuit.b. Sketch the output voltage waveshape.c. Determine the peak value of the output voltage. d. Sketch the input voltage waveshape.e. What is the rms voltage at the input?