Estimate the reinforcing bar of a continuous beam supported by 3 columns (400 mm x 400 mm) spaced at 6 m center to center. The beam measures 300 mm x 700 mm with reinforcing bars as follows: At support: Top bar – 3 pcs of 20mm (continuous bars) for first layer 3 pcs of 20mm (extra bars) for second layer Bottom bar - 3 pcs of 20mm (continuous bars) At midspan: Bottom bar – 3 pcs of 20mm (continuous bars) for first layer 2 pcs of 20mm (extra bars) Top bar – 3 pcs of 20mm (continuous bars) Stirrups 10mm spaced at 180 mm on center.

Estimate the reinforcing bar of a continuous beam supported by 3 columns (400 mm x 400 mm) spaced at 6 m center to center. The beam measures 300 mm x 700 mm with reinforcing bars as follows: At support: Top bar – 3 pcs of 20mm (continuous bars) for first layer 3 pcs of 20mm (extra bars) for second layer Bottom bar - 3 pcs of 20mm (continuous bars) At midspan: Bottom bar – 3 pcs of 20mm (continuous bars) for first layer 2 pcs of 20mm (extra bars) Top bar – 3 pcs of 20mm (continuous bars) Stirrups 10mm spaced at 180 mm on center.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Identify the number of hinge and mode of failure mechanism in the structure as in the figure only HANDWRITTEN answer needed ( NOT TYPED)
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala For the beam loaded as shown, find the maximum tensile and compressive bending stresses and maximum shearing stress.. IN.A=4*10mm* 80mm 100mm 60mm 60mm 1.5KN 2kN/m 1mal A |-----|- | Im ++ Im->> 3m 3kN/m
Q2: Determine (Y). If PA - Pg = 6624 %3D 40 Marks Water Water Mercury 6Y
(Build Cycle Time in Stereolithography) The square cup-shaped part shown is fabricated using stereolithography. The base of the cup is 35 mm on each side and 4 mm thick. The walls are 3 mm thick, and the total height of the cup = 50 mm. The SL machine used for the job uses a spot diameter = 0.25 mm, and the beam is moved at a speed = 1000 mm/sec. Layer thickness = 0.10 mm. Repositioning and recoating time for each layer = 20 sec. Compute an estimate of the cycle time to build the part if the setup time = 15 min. + Tr ni TurntEn T = Tsu + ΣΤ i=1 50
Find the magnitude of the projected component of the force along the pipe. I know the answer is 244N But I don’t understand the steps taken to find it. Please explain Thank you
32 H.W tind longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal Bessure is 0.9 Ma and thickness of Wall is 6.4 mm? Ansi é =42.19 MPa + F= 62.8 Ma Also find ?5067 0.6m 0.6m
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que
3- Calculate the maximum stress suffered by this piece
Determine modulus of elasticity