Answered: Determine whether the block shown is in…

Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when e = 35° and P =200 N. 800 N Hs = 0.20 Hk = 0.15 25°

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A strain gage is installed in the longitudinal direction on the surface of an aluminum beverage can (see figure). 12 FL 02 (366 m) The radius-to-thickness ratio of the can is 190. When the lid of the can is popped open, the strain changes by & = 191 x 10-6. (Assume that the given radius or diameter is an inside dimension and that all internal pressures are gage pressures. Assume E = 10 x 106 psi and v= 0.33.) (a) What was the internal pressure p in the can (in psi)? psi (b) What is the change in strain in the radial direction when the lid is opened? 0.0⁰* Soda Pop
The copper pipe shown in the figure has an outside diameter of 3.000 in. and a wall thickness of 0.383 in. The pipe is subjected to a uniformly distributed torque of t = 87 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.50 ft, and c = 7.75 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. Answers: ccccccccc.com (a) TA= a (b) TB = i b i psi psi
A circular hole is to be punched in a plate that has a shear strength of 40 ksi. The working compressive stress for the punch is 50 ksi. Determine: a) The maximum thickness in inches of a plate in which a hole 2.5 in. in diameter can be punched. b) If the plate is 0.25 in. thick, determine the diameter in inches of the smallest hole that can be punched. Note: Draw the Free Body Diagram, include the units/dimensions, use the proper formula and round-off all the answers and final answers to 3 decimal places.
The copper pipe shown in the figure has an outside diameter of 4.000 in. and a wall thickness of 0.363 in. The pipe is subjected to a uniformly distributed torque of t = 80 lb-ft/ft along its entire length. Using a = 2.00 ft, b = 4.00 ft, and c = 7.5 ft, calculate (a) the shear stress at A on the outer surface of the pipe. (b) the shear stress at B on the outer surface of the pipe. a b Answers: (а) ТА i psi (b) Тв- i psi
1) A brass pipe with a 0.5inch inside diameter and 1/16 inch wall is twisted using a 14inch long pipe wrench. If a load of 74 lbs is applied perpendicularly to the end of the wrench. If the E of brass is 14.6x10^6 psi, what is the max torsion stress in the pipe? • Find the outside diameter of the pipe using the ID and given wall thickness. • Find the polar moment of inertia of the cross-section of the pipe. • Find the torque being applied to the pipe, via the wrench. • Use the torsional stress equation to find the requested stress. Compare your answer: Max Torsional Stress 36.61 ksi
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
Calculate the principal stresses, the maximum tangential stress and their corresponding direction angles.
Angle 1 Tyx Txy x-direction stress 60OMPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: Using a Mohr circle determine the stresses on the plane of the indicated angle 1. (50°). Show al calculations. Draw the orientation of the stress block for this scenario.
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que
SHOW SOLUTION AND DRAW/SKETCH ILLUSTRATION
Help me asap. a 50m long bar lacks 10mm to fit exactly between two fixed supports at 15 deg C. The modulus of elesticity is 230GPa and the coefficient of thermal expansion is 0.0000117/deg C. Find A. The normal stress if the temperature increased to 55 degree Celsius B. Calculate the height of the projectile from the ground after 15 seconds. C. What is the temperature if after thermal expansion, the stress in the bar is 50MPa D. What is the temperature if after thermal expansion, the bar exactly fits between the two supports? E. Calculate the total deformation of bar if at 55 degree C, the bar will exactly fit between the two fixed supports.