What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit) A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 11 KN/m all throughout its length and a concentrated load of 600 N at the midspan. The cross-sectional area of the beam is indicated below.190 mm50 mm180 mm150 mm40 mm190 mm

Find reactions :∑ MB=0RA(4)-11(4)(2)-0.6(2)=0RA=22.3KNRB=22.3KNMAX MOMENT WILL BE UNDER THE POINT…

Answered: entrated load of 600 N at the midspan.…

Engineering

Civil Engineering

entrated load of 600 N at the midspan. The cross-sectional area of the beam is indicated below. 190 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using Centroid by Composite Shapes, determine the x- and y-coordinates of the centroid of the shaded…

A: To find out the x and y coordinates of centroid of shaded area.

Q: For the frame below, determine the forces acting on member AFGH. 1m 0.5 m 0.5 m 0.8 m 0.25 m radius…

A: A frame is given we need to determine the Force acting on the member AFGH In physics, a solid…

Q: A simply supported prestressed concrete beam is 6 m long and 300 mm wide. Its gross depth is 600 mm.…

Q: A 2.5 m rectangular channel carries 6 m3/sec of flow at a depth of 0.5 m. calculate the height of…

A: Given data: b= 2.5 m d= 0.5 m Q= 6 m3/sec

Q: y Given: The shaded area as shown in the figure. 100 mm--100 mm- 150 mm Find: The moment of inertia…

A: step 1-

Q: A small water impoundment for irrigation has a total area of 2,500 m2 with an average depth of 3m.…

A: Given: Total irrigation area= 2500m2, Average depth = 3m, Evapotranspiration rate = 5mm/day = 0.005…

Q: Draw the shear and moment diagram of this beam. 30 kN 4 kN/m 80 kN m B 8 m- 4 m

Q: For the frame shown, the Moment Distribution Method (a) (b)to draw the shear and bending moment…

A: In the above question, a frame is given with all information we need to determine the following…

Q: The section shown below, is subjected to a maximum shear and bending of 5 kips and 25 kips-ft,…

A: Distance of the centroid from the bottom Moment of Inertia of the shape about its centroidal axis

Q: Three wheel loads rolls as aunilacrossa 12 spt The loads areA 15 kN; B-25 kN. 2 m to the right of A…

Q: A small water impoundment for irrigation has a total area of 2,500 m2 with an average depth of 3m.…

Q: A tungsten filament has a temperature of 20.50 degrees Cel and a resistance of 500 ohms wher taking…

A: A tungsten lamp filament has a temperature of 20.5 degrees Celsius and a resistance of 500 ohms when…

Q: 2. Why sand has a low porosity but a high permeability? 3. What factors affect porosity and…

Q: What is the equivalent coefficient of permeability (k) for soil layers of k2 and k3? where k2= 1.75…

A: Given data, K2 = 1.75 k1 K3 = 3.3 k1 To find out the coefficient of permeability for soil layers.

Q: 7-5. The pliers are used to grip the tube at B. If a force of 20 lb is applied to the handles,…

Q: Design a precast concrete pile subjected to an uplift load of 500 kN and a moment of 50 kNm. Use M30…

Q: You take a 10% sample using 1/4 ac plots. If a total of 40 plots were sampled, what is the area of…

A: ASKED: To determine the area of the tract. Given, Sample size (say S) = 10% Plot area (say a) =…

Q: P,=40k P = 80k P- 20k PL = 40k A simply supported beam is loaded at 5 ft and 15 ft from the left…

A: L = 20feet For A992 Fy = 50ksi

Q: testportal Prelim Exams (MEC101) - B06 QuesIu1I 3I 13 ( P.) The forc o

Q: iven the data for a rectangular beam b= 320mm effective depth of 520mm. fc= 27MPA fy=345MPa.…

Q: A small water impoundment for irrigation has a total area of 2,500 m2 with an average depth of 3m.…

Q: The recorded distance is 4572.36m when the temperature is 20° and the pull was 55N supported only at…

Q: Part A Learning Goat To be able to caloulate couple moments A couple is defined as two paralel…

A: In this question we will use the conditions of equilibrium. Then we will find the moment at A and B…

Q: 10. Draw the Free-Body Diagram. Provide a direction and a name for each reaction force and moment.…

Q: Wood. (0.55) L. Concrete Tsp gre25 550mm

Q: Example 10.3 9, eight in number and are hand driven. Estimate the safe inclined load as shown in…

Q: A unit volume of a mass of saturated soil is subjected to horizontal seepage. The saturated unit wt.…

Q: Solve the capacity of a 4.2-m steel column, pin-supported at both ends, having the cross section as…

A: Load carrying capacity = Cross Sectional area * Fy Cross-sectional area = (2*300*45)+(300*55)= 43500…

Q: 12-35. The drainage canal has a downward slope of 0.003. If its bottom and sides have weed growth,…

Q: For the beam shown, calculate the maximum deflection at midspan (Assume I= 150 in", and E = 27500…

A: A loaded beam is given and it has been asked to determine deflection at mid span. Please refer step…

Q: The soil in a deposit underlying an area where a level ground surface exists has a unit weight of 22…

A: Given: Unit Weight of soil = 22 kN/m3, Depth = 5m

Q: Express F as a vector in terms of the unit vectors i, j, and k. Determine the angle between Fand the…

Q: What is the critical depth of the flow in a trapezoidal channel with bottom width 20 ft, slope of…

Q: why tool coating is important?

A: Introduction This question comes from Engineering tool and safety

Q: A fluid is flowing in a pipe 20-cm∅ with a mean velocity of 3 m/s. The pressure at the center of…

A: Given data, Pressure at center = 35 kPa Z = 5 m Velocity = 3 m/s To find out the total head in…

Q: 3. A 300 m3 volume V hydraulic flocculation basin with 24 channels with velocity 0.2 m/s and 23…

A: Flocculation : Flocculation is a condition in civil engineering in which clays, polymers, or other…

Q: Three wheel loads rolls as a unit across a 12-m span. The loads are A = 15 kN; B = 25 %3D kN, 2 m to…

Q: For the given truss system and its loading: which of the first 4 following statements is FALSE? 4m…

A: Since the system is redundant to 2 degree so it is indeterminate to 2 degree Top members of the…

Q: 554. What safe value of W can be applied to the beam loaded as n in Fig. P-554 if o, < 60 MPa and o,…

Q: *12-44. The channel is made of finished concrete and has the cross section shown.If the downward…

Q: 3. Route the inflow hydrograph using Muskingum method; hr, = 0.2, = 0.65 hrs. %3D Time 01 2 3 4 5 6…

A: Given : Muskingham method Time and Inflow rate is given K = 0.65 hrs x = 0.2 t = 1 hrs

Q: A sand fill has an initial void ratio of 0.740, it was then compacted to achieve a desirable void…

A: solution inital void ratio e=074desirable void ratio emax=0.4specific gravity G=2.7γdmax=1903.36…

Q: Determine the Members' Force for the following Truss using the Direct Stiffness Method. P ton EA EA…

A: Types of stiffness: 1) Axial Stiffness: Axial load required to produce a unit axial displacement is…

Q: You are strip cruising with 1 chain wide strips and the total length of your strips is 100 chains,…

A: step 1-

Q: rectangular deck scow 35.0 m long, 5.60 m wide, and 3.50 m high has a draft of 1.30 m when light ad…

A: Given: Length of scow bottom, lb = 24m Length of scow deck, Ld = 35m, Width of scow deck, Wd = 5.6m,…

Q: Design a bored pile carrying a compressive load of 1000 kN and a moment of 50 kNm. Use M25 mix and…

Q: What is the equivalent coefficient of permeability (k) for soil layers of k2 and k3? where k2= 1.75…

A: To find equivalent permeability

Q: W = 5, P=40 2. Solve for the Slope at B and the support reactions of the beam shown below using both…

A: Slope deflection method: The slope deflections methods is one of the methods used in structural…

Q: 521.. A channel width is 0.312 m. A venture flume having a throat of 5.6 inch was set in the…

A: In this question, we will use the relation between the metre discharge and the theoretical…

Q: How did we get the 0.3 which is used on the solving the grade of the road?

A: Data Given: Asked: How did we get the 0.3 which is used on the solving the grade of the road?

Concept explainers

Planar Stresses

Question

What is the actual bending stress of the beam in MPa? (use two decimal places, no need for unit)

A simply supported 4-m long beam is made up of 80% grade Malugai. The beam is carrying a uniform load of 11 KN/m all through
out its length and a concentrated load of 600 N at the midspan. The cross-sectional area of the beam is indicated below.
190 mm
50 mm
180 mm
150 mm
40 mm
190 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q2 The simply supported beam supports an axial compressive load 20 kN as shown below. Determine the resultant stresses in both top and bottom fiber at mid of the span. Draw the distribution of stresses. 100 mm 500 mm NA -20 kN 20 KN 6.0 m 300 mm 1 F Amm X B
A cantilever beam has a span of 3 m. The beam carries a uniform service load w = 22 kN/m includes the weight of the beam. There is no lateral support other than that at the fixed end. Properties of W 10 x 77 A = 14581 mm2 Lp = 2.799 m d = 269.24 mm Lr = 13.811 m bf = 258.83 mm Lb = 3 m tf = 22.10 mm Fy = 345 MPa tw = 13.46 mm K = 38.10 mm Sx = 1408 x 103 mm3 E = 200,000 MPa Zx = 1599 x 103 mm3 a. Determine the value if the service load P due to the max. shear strength of the beam using LRFD. b. Determine the value if the service load P due to the max. shear strength of the beam using ASD. c. Determine the value of the service load P due to the flexural strength of the beam using LRFD. d. Determine the value of the service load P due to the allowable bending strength of the beam using ASD.
The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension in MPa? 240 mm T- W 12 KN/m 60 mm 200 mm 4 m 4m 60 mm 165.856 202.967 105.802 none among the choices
Problem 4 The beam loaded as shown below, compute the bending stresses at every 1m from the fixed end support of the beam use Ina = 100x106 mm4 www 10 kN 4 kN/m bm 러 n.a. 130 mm 200mm
Situation 5: A cantilever beam having a span of 4 m carries a uniform distributed dead load of 30kN/m throughout its span. The beam is W 21 x 62 A50 steel with yielding stress of Fy = 345 MPa Properties of W 21 x 62 A = 11800 mm² Wb = 92 kg/m d = 533 mm bf = 209 mm tf = 15.6 mm tw = 10.2 mm rts = 54.6 mm ry = 45.0 mm kdes = 28.4 mm Sx = 2080 x 10³ mm³ Zx = 2360 x 10³ mm³ J = 762 x 10³ mm³ Cw = 1600 x 10 mm 1. What is the Ultimate moment load capacity of the beam?? 2. What is the Ultimate moment load capacity of the beam? ( 3. What additional live load that can be add to the beam so that it will not exceeds its ultimate moment
A simply supported girder spans 10 m. It carries two beams, each at 3.5 m from the supports. The concentrated load from each beam is 70 kN. Properties of W 410 mm x 100 kg/m d = 410 mm A = 12710 mm² = 260 mm bf tf = 17 mm Ix = 397x106mm4 ly = 49x106mm4 tw = 10 mm F, = 248 MPa a) Which of the following gives the maximum web shear stress (MPa)? b) Which of the following gives the maximum horizontal shear stress (MPa) at the neutral axis?
What will be the safe weight per linear meter length of the beams if the displacement at E is limited at 8mm. Where x=14.37m. = Properties of Steel: Ast 300mm², Est-200 GPa, Lst=2m = Properties of Steel: Aal 500mm², Eal-70 GPa, Lal=2m 0:5X Whit ALUMINUM x STEEL с
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
The beam is loaded as shown. which of the following nearly gives the flexural stress due to tension in MPa? 240 mm W = 12 KN/m 60 mm 200 mm 4 m 4 m 4 m 60 mm 202.967 none among the choices 165.856 105.802 OO O O
An 8 m long steel is simply supported at the left end and 2 m from the right end. It carries a total uniform load of 45 kN/m all throughout its length. STEEL DECION CIVIL ENGINEERING Beam properties: A= 11,500 mm² bf = 250 mm tw- 10 mm d = 350 mm If=: 16 mm lx = 266 x 100 mm If the Beam is laterally supported throughout the beam b) Determine the Maximum Web Shear Stress
x steel beam 12m long is fixed at both ends and carries a superimposed uniformly distributed load of 35kN/m. The beam is W18x46 whose relevant properties are shown below. Properties: Flange width bf= 153.9mm Flange thickness tf= 15.4mm Overall depth d= 458.7 Web thickness tw = 9.1mm Bearn weight = 68.5kg/m Moment of inertia = 296, 357x10 ³mm² Which of the following most nearly gives the maximum shear stress in the web? Select the correct response: 48.22Mpa 54.92Mpa 58.22Mpa 34.92Mpa
A steel beam 12m long is fixed at both ends and carries a superimposed uniformly distributed load of 35kN/m. The beam is W18x46 whose relevant properties are shown below. Properties: Flange width bf=153.9mm Flange thickness tf = 15.4mm Overall depth d= 458.7 Web thickness tw- 9.1mm Beam weight = 68.5kg/m Moment of inertia = 296, 357x10 ³mm4 Which of the following most nearly gives the maximum bending stress in the beam? Select the correct response: 165.56Mpa 331.27Mpa 231.27Mpa 185.56Mpa