Consider the circuit below shown in Figure Q2 with terminals a-b. a) Figure Q2(a) shows the circuit after the independent sources were deactivated. Find RN. b) Figure Q2(b) shows the circuit after terminals a-b were shorted. Find Isc. c) Draw the equivalent Norton circuit. 20 4Ω 20 4Ω 12V www www 8 Ω 8 Ω www 8 Ω 8 Ω www 5Ω Figure Q2 5Ω www Figure Q2(a) 8 Ω 4 Ω στο 6 Ω 12V 8 Ω www Figure Q2(b) 50 www 50 5Ω a b RN 1sc = IN

Consider the circuit below shown in Figure Q2 with terminals a-b. a) Figure Q2(a) shows the circuit after the independent sources were deactivated. Find RN. b) Figure Q2(b) shows the circuit after terminals a-b were shorted. Find Isc. c) Draw the equivalent Norton circuit. 20 4Ω 20 4Ω 12V www www 8 Ω 8 Ω www 8 Ω 8 Ω www 5Ω Figure Q2 5Ω www Figure Q2(a) 8 Ω 4 Ω στο 6 Ω 12V 8 Ω www Figure Q2(b) 50 www 50 5Ω a b RN 1sc = IN

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter7: Parallel Circuits

Section: Chapter Questions

Problem 4PP: Using the rules for parallel circuits and Ohmslaw, solve for the missing values....

See similar textbooks

Similar questions

Refer to the circuit on the right. VEB = 0.7 V, when the BE junction is conducting. VECsat = 0.2 V B Vref = 2.2 V (Use two decimal places.) = ∞ VREF IL +5 V R LOAD Figure 2 a. What should be the value of R in ohms if IL is to be maintained at 146 mA under changing load conditions? b. In order to maintain this load current, what should be the maximum allowable load resistance in ohms?
Repeat Problem 3 for the circuit of Figure d.
Urgent please In the circuit shown in the figure, the RL load is connected to a 20 V source when switch K is in position 1; In this position, draw the waveforms of the welding voltage, the voltage at the R end, the voltage at the L end and the current 1.
Six 100Wp crystalline PV modules, each with an open circuit voltage (Voc) of 30V, are connected in series in a string. What would be the total open circuit voltage (Voc) of the string of modules? And what would be the total Wp of the string? 180V, 600Wp 180V, 100Wp 30V, 600Wp 30V, 100Wp The distance from a combiner box to a PV array junction box is 4 m. The voltage drop of the used cable on this distance is 0.5 V. The current is 8.0 A. What is the power loss on this distance? 16 W 32 A 4 W 2 W A PV system has a rated capacity of 10 kWp. The overall efficiency of this PV system is 75% . The average daily irradiance at the site is 4 kWh/m²/day. What is the expected average daily energy output of this system? 3 kWh 30 kWh 7.5 kWh 40 kWh
For the circuit below, determine the resistor current. The source is 8 volts, the Zener potential is 5.2 volts and the resistor is 5k ohms.
Using the rules for parallel circuits and Ohmslaw, solve for the missing values. ETE1E2E3E4ITl1I2l3l4RTR182kR275kR356kR462kPT3.436WP1P2P3P4
For the circuit below, determine the resistor voltage. The source is 6 volts, the Zener potential is 5.1 volts and the resistor is 1k.
In the circuit given in the figure, Rk = 1.93Kohm, R1 = 2071.88Kohm, R2 = 1678.12Kohm, R3 = 2.84Kohm, R4 = 0.95Kohm, R5 = 26.02ohm, Ry = 95.53Kohm, VCC = 15.00V, VTN = 2.40V, Kn = Since it is 2.30(mA/V^2), C1= 5.80uF, C2= 5.20uF, C3= 7.73uF, calculate the lower cutoff frequency of the circuit in Hz.
What is the load current for the circuit shown in the figure? Please choose one: a. 9.0 mA b. 7.5 mA c. 3.0 mA D. 6.0 mA
Consider a typical electrical circuit system shown in Figure 2. The circuit consisting of two resisters value R, and R2 (ohm), a capacitance of value C (farad) and an inductance of value L (henry). The input is the supplied voltage V, and the output voltage is Vo- viz R1 Vi R2 Vo Figure 2 (1). Apply Kirchhoffs voltage law or other principles to derive the input-output dynamic model equation. (i). Apply Laplace Transform to determine the model transfer function for the electrical system. (i). Estimate the transfer function for the following R; = (ohm) and R2 = (ohm), L = (henry), and C = (farad) values. Task 4 R, (ohm) R: (ohm) C (farad) (henry) Note: Refer the Table for R1, R2, C and L values. 27 13 24 4 lellll
Draw AC and DC equivalent circuit for the circuit given in Figure 4
need fast. show circuit diagram