Each of the four links in Figure 3 has an 8x36mm uniform rectangular cross section and each of the other four pins has a 16mm diameter. a. Determine the maximum value of the average normal stress in the links connecting points B and D and points C and E. b. Determine the average shearing stress in points B and C.

Q: a. Take a cut through the section where the AB and BC segments are connected (shown in the figure at…

A: we are to determine the stress distribution  at section B, and the load at point C

Q: Question 2) Forces of F1=3 kN in the z direction from point B, F2=9 kN in the z direction from point…

A:

Q: 1. The solid shaft is fixed to the support at C and subjected to the torsional loadings as shown…

A:

Q: Two steel springs arranged in series support a load p the upper spring has 12 turns of 25 mm…

A: Given data: n1=12 turnsd1=25 mmR1=100 mmn2=10 turnsd2=20 mmR2=75 mmτmax=200 MPaG=83 GPa Need to…

Q: The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA…

A:

Q: 7. Determine the stress developed in the Tensional Cord given that the cable’s diameter is 0.6…

A: Given, Weight of the bar = W = 6 kips Diameter of cable = d = 0.6 in AB = 5 m BD = 3 m BC = 5 m…

Q: Seven 7/8-in-diameter rivets fasten the plate to the fixed member. Determine the maximum and minimum…

A:

Q: The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and…

A:

Q: A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim…

A: Given:Force applied by the player (F) = 320 lbsOutside length of the square tube (L) = 5…

Q: Solve Problem for the maximum shear stress within regions AC and BC, and the angle of twist f of end…

A: Considering Section AC, Maximum Shear Stress: Considering Section BC, Maximum Shear Stress:

Q: The lap joint is fastened with four 3/4-inch diameter rivets. ➤a. If the allowable shearing stress…

A:

Q: The 20 mm diameter rod is subjected to the loads shown. (a) Determine the state of stress at point 4…

A: Diameter, d = 20 mmIt is asked to find the stress at point A and draw the state of stress using…

Q: Determine the torsion on the rigid supports and the maximum shearing stress developed in each…

A:

Q: The rectangular bar shown is connected to a support bracket with a 24 mm diameter pin.  The width of…

A: Given Data The diameter of pin is:d=24mm=24×10-3 m The width of the rectangular bar is:b=70…

Q: (D) The pin used at B has an ultimate shear strength of 58 ksi. If a factor of safety of 2.5 is…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A: Consider below figure for the given question: We are given, Load = P = 2000 lb Diameter of pulley =…

Q: A force of 120 lb is applied to the edge of the member shown in the figure below. Neglect the weight…

A: given: P=120 lb Solution: Maximum bending moment is given as : Mmax=P×4.5=120×4.5=540 lb-in

Q: A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal…

A:

Q: Problem 1: If the parts of the shaft below are a 1" diameter solid steel rod and a 2" OD diameter…

A:

Q: 10/.. find the shear stress in bolts 4 80 kN 80 kN -O- O--O- 300 mm

A: Write the expression for the load acting on the riveted joint.

Q: 1. A hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400 lb.…

A: Given: P = 400 lb d = 100 mm stress = 12 MN/m2

Q: A cantilevered solid shaft with length of 400-mm and diameter of 150-mm is loaded at its free end as…

A:

Q: 2: haft shown below, determine the normal and A, including stress concentrations. Then dr and…

A: Given: r=0.0042 m d=0.03 m D=0.033 m P=1500 N M=300 Nm T=250 Nm

Q: Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of…

A: given data  force p= 2 kips dimension of cross section= 1.6 ×1.6 in^2 find the combined stress at…

Q: The lap joint shown is fastened by 4 rivets of ¾ in. diameter. Find the maximum load P that can be…

A: Given Data: Diameter of rivet, d=3/4 inch Working shear stress, 14000 psi Working bearing stress,…

Q: The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear).…

A:

Q: Q.1:Answer only one from a & b: a: At a certain point in a stressed body, the stresses are ox= 30…

A: Given: The stress on the x phase is σx=30 MPa The stress on the y phase is σy=-25 MPa The shear…

Q: Solve using Mohr's circle

A: For the given state of stress, To find: The normal and shearing stresses after the element has…

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: Since each of the shafts AB, BC and CD shown in the figure consists of a solid circular bar,…

A:

Q: The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form…

A: To find: The greatest value of thrust and the stress along the face AB. Given: The tensile stress…

Q: A.) If the F = { - 200i + 400j } N , determine the force in each member and state if its in…

A:

Q: On section a-a, determine the stress state at points A & B. Neglect the weight of the block. If the…

A: Find:stress state at point A and B

Q: 2. Determine the shear, tensile and bearing stresses on a double riveted butt joint with ¾ in. main…

A:

Q: A 6" diameter pulley attached to a 1" diameter shaft of 2" length is supporting a load of 2000 lb.…

A:

Q: Two 2 by 4 cm 1062 steel bars are butt-spliced with two 3 by 4 cm 1016 splice plates using six M14…

A: We have to find the correct formula for finding shear stress

Q: A flanged bolt coupling consists of eight 10-mm diameter steel bolts on a bolt circle 400 mm in…

A: Given:no=8do=10 mmDo=400 mmni=6di=10 mmDi=300 mmFo=8000 N

Q: ach have a 20-mm diameter and happen to be parallel in the position shown. Take P = 900 N.…

A: Stress:- The load operating on the body in the unit area when a body is subject to the limitation…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.