A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitud are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c = 5 in. Determine the normal and shear stresse on the outer surface of the pipe at point H and show these stresses on a stress element. b Pz Py

A hollow crank with an outside diameter of 4.0 in. and a wall thickness of 0.19 in. is subjected to the loads shown. The load magnitud are Py = 710 lb and P₂ = 355 lb, and the length dimensions are a = 14 in., b = 7 in., and c = 5 in. Determine the normal and shear stresse on the outer surface of the pipe at point H and show these stresses on a stress element. b Pz Py

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.3.1P: The stresses acting on an element are x= 750 psi, y= 600 psi, and xy = 400 psi. Determine the...

See similar textbooks

Similar questions

‘7.3-11 The stresses on an element are sx= -300 psi and sy= 600 psi. Find the maximum shear stresses on the element and show them on a sketch of a properly oriented clement.
The state of stress on an element along the hydraulic lift cylinder on a truck is trv= — 5 MPaLFind the maximum shear stress on the clement and show the state of stress on a sketch of a properly oriented clement.
IN THE SYSTEM SHOWN AS BELOW, A FORCE OF 200 N AFFECTS ON THE PIPE SWITCH. CONSISTING AT POINTS A AND B ON THE PIPE ACCORDING THAT THE PIPE'S DIAMETER IS 25 mm; SHOW THE PRIMARY STRESSES AND PRIME AXES (principal axis directions) ON THE MOHR CIRCLE.
A steel pipe 120 mm external diameter and 60 mm internal diameter is subjected to an internal pressure of 15 N/mm2 and an external pressure of 5 N/mm2. Determine and sketch curves showing the distribution of the radial and circumferential stress across the section using Lame’s equations.
Q1: The C-shaped steel bar has cross section of a square of side 1.6 in. If the magnitude of p=2Kips.find the combined stresses at point A. 3.2 in. 1.6 in.
Forces of Px = 580 lb and Py = 220 lb act on the teeth ofthe gear shown in Figure 1. The gear has a radius of R =6 in., and the solid gear shaft has a diameter of 2.0 in.Using a = 5 in., determine the normal and shear stressesat (a) point H and (b) point K. Show the orientation ofthese stresses on an appropriate sketch.
Find the Principal Stresses on the tube below given the forces in the X,Y and Z axis shown below: Radius: R2=5mm R1=4mm and τxy= 0.1 Pa
5. A cylindrical pressure vessel has an inner diameter of 4 ft. If the yield strength for the tank material is 36 ksi and the internal pressure is 150 psi, what is the factor of safety if the wall is 0.35 inch thick? 6. For the state of stress shown, draw a Mohr's circle (mark two stress points and average normal stress value) Find the two primary principal stresses (oa and Ob) Find 01, 02, and 03 . Find maximum shear stress value. Vrms. From faliure critera, find factor safety using Tresca and Von Mises methods. (consider Oy = 36000 psi) 1500 psi 200 psi 2500 psi
A machine component is fabricated from a bent tube as shown below. One part of the tube lies along the z- axis, and the other part is parallel to the y-axis. The outside diameter of the tube is do 122 mm and its inside diameter is dį = 108 mm. A force F = 8.5 kN acts along a line from point to point D. Determine the principal stresses and the absolute maximum shear stresses at points A and B. Note that point A lies along the y-axis and point Blies along the x-axis. Given: • L₁ 258 mm L₂ = 118 mm • L -281 mm LA-602 mm 4 P (α₂₁)A- (₁2) A (Tmax) A L2 Z ²1 00 B L₁7 number (rtol=0,01, atol=1e-05) number (rtol-0.01, atol-1e-05) number (rtol-0.01 atol-le-057 F 0 MPA LA D L3 y 0 0
Determine the stresses at points A and B as a results of applying each of the following internal loads N = 300 N, V = 250 N, M = 120 N.m and T = 300 N/m. The diameter is 20 mm. You must show your detailed solutions
1. A loaded bicycle pedal crank is shown below. q 750N (2 direction) 72/ A @ Top 8 yo B@ Top d = 15 mm x₁ = 125 mm x2 = 24 mm y₁ = 60 mm у2=X2 a. Sketch elements A and B and show the stress states. Clearly label the coordinate axes on the elements. Make sure you calculate the normal (o) and shear stresses (T). Do not neglect Tv. Find the principal stresses for each element using Mohr's Circle. b.
Neglecting the weight of the bracket, calculate the three principal stresses, and absolute maximum shear stress at point A on the cross section of the bracket at section a-a. Calculated for you: Iz = 0.79948 in“, cross sectional area is 0.875 in². 0. in. 0.25 in. 0.25 in---|-0.25 in. 6 in. I.s in'1.5 in. L Section a-a 12 in.