The 32-in diameter pump has a performance curve as below. The pump is used at 1170 rpm in a system whose head curve is hp = 110 + 1.5Q2 (in ft), with Q in units of thousands of gallons of waterper minute. Please estimate the discharge required for one pump installed in the system.Total head, ft8007006005004003002000O 20000 GPMO 15000 GPMO 12500 GPMO 17500 GPMn = 1170 r/min36-in dia.32-in dia.28-in dia.8NPSH11500 bhp.87%88%2000 bhp3000 bhp87%12162024U.S. gallons per minute x 10003500 bhp2500 bhp2850403020NPSH, ft

Here we will refer to the curve to get two points to calculate the constant of the head and…

The 32-in diameter pump has a performance curve as below. The pump is used at 1170 rpm in a system whose head curve is hp = 110 + 1.5Q2 (in ft), with Q in units of thousands of gallons of water per minute. Please estimate the discharge required for one pump installed in the system. 800 n=1170 r/min NPSH 50 40

The 32-in diameter pump has a performance curve as below. The pump is used at 1170 rpm in a system whose head curve is hp = 110 + 1.5Q2 (in ft), with Q in units of thousands of gallons of water per minute. Please estimate the discharge required for one pump installed in the system. 800 n=1170 r/min NPSH 50 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water at 20"C Bows through the pump impeller shown in the figure below, where the inner and outer diameters of the impeller are 160 mm and 400 mm respectively, and the width of the pump blades is 55 mm Part A Wan- μA Estimate the shaft power required to drive the pump at this operating condition Express your answer to three significant figures and include appropriate units. Value Blade Pump impeller The impeller rotates at 3600 rpm Under a particular operating condition, water enters in a direction normal to the inflow surface, the component of the outflow velocity normal to the outflow surface. V is equal to 17 m/s, and the magnitude of the absolute velocity, V, at the outflow surface is 33 m/s Submit Request Answer Units Outflow surface Inflow surface ? 160 บท 400 mun
A gear pump has a 80-mm outside diameter, a 55-mm inside diameter, and a 25-mm width. If the actual pump flow rate at 2300 rpm and rated pressure is 140 LPM, calculate the Displacement Volume, VD (m3) Group of answer choices 66.9x 10-7 m3 56.3 x 10-6 m3 66.3 x 10-6 m3 97.1 x 10-7 m3 70.9 x 10-6 m3
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised flow rate? Select the correct response: 176.21 gpm 76.21 gpm 89.66 gpm 98.85 gpm 289.66 gpm 198.86 gpm
It is desired to deliver 4 gpm at a head of 670 m in a single pump having specific speed not to exceed 40. If the operating speed is not to exceed 1352 rpm, how many stages are required? Select the correct response: 0 7 O 5 3 6 Contin 2.
A centrifugal pump equipped with a variable frequency (speed) drive running at 3500 rpm is discharging 240GPM corresponding to a head of 287ft. The horsepower is 35.5. if the pump's speed is reduced to 2900 rpm, what will be the revised power required? Select the correct response: 29.32 hp 20.19 hp O 24.37 hp 29.41 hp 34.23 hp 30.37 hp lenovo
Figure below shows the performance curve family of Model 5009 Centrifugal pumps of Taco Pump Inc., running at a fixed speed of N = 1160 rpm. For the pump with the impeller diameter D = 8.625 in., you are asked to determine the best efficiency point (BEP) of the given pump. What is the pump efficiency at BEP? HEAD IN FEET 50 0 0 0 0 40 20 10 O 81% 8.625" 30 (219mm). O 51% O 71% ○ 61% O Taco L/SEC 5 9.25" (235mm) 8.00" (203mm) 7.375" (187mm) 6.75" (171mm) 0 10 15 125 Model 5009 FI & CI Series 20 25 CURVES BASED ON CLEAR WATER WITH SPECIFIC GRAVITY OF 1.0 8 8 52 75% 77% 30 79% 1160 RPM FEBRUARY 19. 2002 35 40 45 REQUIRED NPSH olº 1.5HP (1.1KW) dot 17% Curve no. 2140 Min. Imp. Dia. 6.75" Size 6 x 5 x 9.0 50 55 60 75% 72% 250 375 500 625 FLOW IN GALLONS PER MINUTE 8% 2HP(1.5KW) 750 %09. 55% (2.2KW) 3HP 7.5HP(5.6KW) 2015 do 35% 875 FEET 15 12 -9 6 SHP(3.7KW) 3 0 10 8 NPSH 1000 HEAD IN METERS 5 KPo 45 -36 27 18 9 -0 100 -80 60 -40 2 -20 8 HEAD IN KILOPASCALS
A single stage centrifugal pump has an impeller of 250 mm diameter which rotates at 1,800 rpm and lifts 60 lit/sec to 25 m with an efficiency of 70%. Obtain the number of stages and diameter of each impeller of a similar multi-stage pump to lift 75 lit/sec to 175 m at 1,500 rpm. (8 stages ; 280 mm dia)
This course EHide block A centrifugal pump with the following impeller dimensions is used to pump water. The pump is running at 1000 rpm. The ideal head rise through the pump is 190 ft. b2 Poz 72 by The parameters of the impeller are as follows: r2= 9in, b2=3in, B2= 31° Take g= 9.81 m/s23 32.2 ft/s2 pw = 998 kg/m3 = 1.94 Slug/ft. Determine the theoretical flow rate in gpm Choose.. Determine the theoretical Power shaft in (hP) Choose...
Refer to the “composite performance chart” for a Goulds 3x4-10centrifugal pump operating at 1750 rpm. It shows the pump performance curve for 5 differentimpeller sizes, but also shows the HP required, efficiency, and NPSH required at differentoperating points.Describe the performance of this pump, using an 8 inch impeller and a required flow rate of175 gpm. Give head available, power required (BHP), efficiency, and NPSH req’d. What is the water horsepower (WHP)?
Q Consider the following data relating toperformance of a centrifugal pump:speed 1200 rpm, flow rate 30 L/s, head 20 m, and power 5 kW. If the speed of the pump is increased to 1500 rpm, assuming the efficiency isunaltered, Find the new flow rate and head.
4. A pump is used for the pumping of water from Tank A into Tank B in which the height difference between the surface levels of water is 20 m. The pipe diameter is 400 mm and the pipe length is 2500 m, the coefficient of friction is f 0.0025 and the pump works at a speed of 700 rpm. The characteristics of the pump are shown in Table 4 below You are required to: (a) (10 points) Intepret pump characteristic and system characteristic ina graph. (b) (10 points) Calculate the input and output power at the operating point. 0.1 0.2 0.3 0.35 0.4 0.5 15 17 18 16 14 O30 60 SI83.80 45 H. (m) 11 Table 4: Data of the pump from the Manufacturer
Pump has a displacement of 98400 mm. It delivers 91.2 Lpm of oil at 1000 rpm and efficiency is 81.7 %. If the prime mover has input torque is 12430 N-cm, find the value of pressure. Select one: O a. 6.99x10° N/m O b. 699.2x10° N/m 2 O C. 69.9x10° N/m 2 O d. 6.99x10° N/m