Determine which of the three states of stress shown is most dangerous. The numerical values of stresses are given in MPa. The material has the same mechanical properties in tension and compression. (Note that there are no relations among any of the shown blocks). ODET J00 800 600 750 100 (a) (6) (c)

Determine which of the three states of stress shown is most dangerous. The numerical values of stresses are given in MPa. The material has the same mechanical properties in tension and compression. (Note that there are no relations among any of the shown blocks). ODET J00 800 600 750 100 (a) (6) (c)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

answer as soon as soon as possible
(1) by Given: P B (2) (3) ↑ D P=28 kN R = 38 kN Square Bars b₁ = 57mm 6₂ = 19mm b3 = 38mm WHAT IS THE AXAIL STRESS IN BAR 2? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES. POSITIVE FOR TENSILE STRESS AND NEGATIVE FOR COMPRESSIVE STRESS. R P Q =9 kN
Please provide correct solution and fast
For a given homogeneous, isotropic, linearly elastic material, E = 15e6 psi and v = 0.3. Solve for the shear modulus. 2.1.1 Homogeneous, isotropic, linearly elastic materials For specimens undergoing small deformations, the stress-strain diagram often ex- hibits a linear behavior. Although this is a very crude approximation to the behavior of actual materials, it is a convenient assumption that is often used for preliminary evaluation. A linear relationship between stress and strain can be expressed as 01 = E €1, (2.1) where the coefficient of proportionality, E, is called Young's modulus or modulus of elasticity. Since strains are non-dimensional quantities, this coefficient has the same units as stress quantities, i.e., Pa. This linear relationship is known as Hooke's law. The elongation of a bar in the direction of the applied stress is accompanied by a lateral contraction that is also proportional to the applied stress. The resulting defor- mations for this uniaxial state of stress…
need help with this Mechanics of Materials
i li. الامتحان هو سؤالان فقط Q. 1: If a material is cast iron (ultimate tensile strength = 300 Mpa, ultimate compressive strength - 900 Mpa) and the stress state at a point is shown in Fig. 1. Using a graphical method, find safety factor against static failure using 100 Mpa (a) Rankine failure theory (b) Coloumb - Mohr theory (c) Modified Coloumb - Mohr theory 50 Мра إضافة ملف Q.2 For a rotating shaft of diameter 15 mm as shown in Fig. 2. If the material is AISI-1045 CD, Find the safety factor II >
A steel component is subjected to alternate cyclical loading. The steel follows Basquin's law for high cycle fatigue, o, x N = C, (where the stress amplitude is in MPa). Ignore the geometric detail and assume that Marin's modifying factors are all equal to 1. You are given the minimum stress ain = -213 MPa, the maximum stress omax = 213 MPa. The material data are Tensile strength oUTS = 539 MPa, Basquin's constant c, = 875 MPa, Basquin's exponent a = 0.085. a) Calculate the stress ratio R, the stress amplitude o, in MPa and the mean stress am in MPa. The answers are acceptable with a tolerance of 0.01 for R and of 1 MPa the stresses. R: MPa MPа b) Calculate the corresponding life, in 10° cycles, (tolerance of 0.1 106 cycles) N :
Calculate the principal stresses to the given state. Calculate the angle of rotation in the x-y plane. Calculate the extreme shear stresses. Are the extreme shear stresses the maximum shear stresses? Explain, Why or why not?
The state of stress at a point in a component is represented by a Mohr's circle of radius 100 MPa centered at 200 MPa on the normal stress axis. On a plane passing through the same point, the normal stress is 260 MPa. The magnitude of the shear stress on the same plane at the same point is MPa. ६ R=100 200 260.
Please provide the correct solution asap. Handwritten recommended
7:Y. O %Y. O 36 ll ll くロ quiz 2 elearning.uowa.edu.iq Marked out of 1.00 P Flag question quiz 2: flexural stress which fluctuates between + 250 MN/m2 and - 115 MN/m² applied on a machine component. Calculate the ultimate strength value according to Goodman's relation. Take yield strength = 0.55 Ultimate %3D strength; Endurance strength = 0.5 Ultimate strength; and factor of safety = 1.5. A- В I D II