Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed=60 mph, max superelevation=8% 7) The difference in elevation of LEP and REP at PC/PT, in ft, is: 0 0 O 0.42 O 1.68 O 2.52 O 3.36

Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed=60 mph, max superelevation=8% 7) The difference in elevation of LEP and REP at PC/PT, in ft, is: 0 0 O 0.42 O 1.68 O 2.52 O 3.36

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed%3D60 mph, max superelevation=8% 6) The length in full superelevation, in ft, is: O 790 O 1100 O 1410 O 1875 O 2075
Just do question 2
Given the proposed longitudinal profile of the centerline of a rural two-lane highway as follows: PVLu STN 10+0) PVL: Elev. 100 ft G-2% Ge0% L=? Ly=? a) Calculate the required minimum design lengths (to meet the SSD requirements) of the three back-to-back vertical curves on this section of the roadway to accommodate a continuous design speed of 50 mph.
Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed=60 mph, max superelevation=8% 3) The Lr of the curve, in ft, is: 77.5 O 310 692 1200 1255
A vertical curve joining a (-5%) and (+3%) grades in a rural highway has a design speed of 100kph. The tangents intersect at a station (225+71.35) at an elevation of 290m. Caleulate the elevations of intermediate points on the curve each 100m, and determine the stations and elevations of PVC, PVT. It s important to know that the driver acceleration rate is 3m/sec2 and the perception & reaction time is 2.5 seconds.
A. Reversed curve with diverging tangents is to pass through three lines to form a center line of a proposed road. the first line AB has a bearing of N 88° E. and a distance of 125 m., BC has a bearing of N 60° E and a distance of 350 m., while on that of CD has a bearing of S 40° E and a distance of 305 m. If the first tangent has a distance of only % of the common tangent measured from the point of intersection of the first curve determine the radius of the curves and station of PT if PC is 12 + 350
2
Determine variables requested below for a horizontal curve with the following characteristics. Length of curve 1255', Radius 1200', sta of PC 12+00 superelevation rotated about the roadway centerline, 3 lane roadway, 14ft lane width, entire road section normal crown=2%, road design speed3D60 mph, max superelevation=8%. 9) The difference in elevation of LEP and REP at NC, in ft, is: O 0.42 O 1.68 O 2.52 O 3.36
ans No. 3 only. asap
A vertical curve is formed on a two lane undivided highway between the tangents of 1 gradient + 1 Assume the height of driver's eye and height of obstruction and 100 50 as 1.4 m and 0.18 m respectively. Determine the length of vertical curve so formed considering stopping sight distance calculated using the following parameters. Design speed of vehicle = 80 kmph Reaction time = 2.5 sec Down gradient = 2.5% Coefficient of longitudinal friction = 0.38
Determine the values and stationing (sta. PT) for a compound curve to be placed on an exist loop of a freeway. The stationing of the loop construction will start at the point the taper departs the freeway with a station of 10+00. The Pl of the compound curve will begin 2,700ft after the taper starts. The first curve has a radius of 2,400ft and a deflection angle of 33° 45' and the second curve has a radius of E (Ctrl) 1,900ft and a deflection angle of 25° 15'.
Show work and answer question 7 only