Determine the velocity and pressure at sections 2 and 3 if water flows steadily through the pipe system shown in Figure. Assume a head loss of 6 ft from section 1 to section 2 and of 15 ft from section 2 to section 3.

Determine the velocity and pressure at sections 2 and 3 if water flows steadily through the pipe system shown in Figure. Assume a head loss of 6 ft from section 1 to section 2 and of 15 ft from section 2 to section 3.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Compute the discharge through a 1000 mm diameter pipe flowing at an velocity of 1.5 m/s.

A: Given: Diameter of pipe, d = 1000 mm Velocity, v = 1.5 m/s

Q: Consider the steady flow in a water pipc joint shown in the diagram. The areas are: A= 0.2 m. Az =…

A: Mass flow equations give the relation between the outlet and inlet pipes properties. The equation…

Q: Q/Consider steady, incompressible and flow through a reducer in a horizontal pipe where the diameter…

A: d1=20cm d2=10cm P1=150kPa P2=50kPa

Q: a. Determine the velocity of flow in the pipe in fps. b. Determine the discharge Q in ft^3/s.…

A: Apply bernoulli equation.

Q: PROBLEM 6 A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At…

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

Q: For the sluice gate shown, if C=0.90 what is the flow rate? If C=0.71 what is the height of the…

Q: From the looping pipe system shown, Pressure heads at points A and E are 70m and 46m, respectively.…

A: Q= 0.228 m3/sec

Q: A 20 mm diameter copper pipe (19.94 mm inside diameter) carries water at a flow rate of 40 L/s.…

A: The expression for the discharge is given by, Q=AV Here, Q is the discharge, A is the area of cross…

Q: PROBLEM 6 A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At…

Q: Q-1 Following figure shows a system in which water flows from a tank through a pipe system having…

A: The expression for Bernoulli's equation is given as:…

Q: a) Determine the head loss in the “smooth” pipe in meters if the friction factor is 0.014. b) What…

A: When a real flow takes place, some resistances act against the flow. The energy given away by the…

Q: As part of a flow and pressure analySIs, a rectangular pipe loop with a length m and width of 300 m…

A: Equivalent pipe means a pipe which can replace existing compound pipe while carrying same discharge…

Q: Assume frictionless flow in a long, horizontal, conical pipe, which has a diameter of 3.6 ft at…

A: Given: The entrance diameter of the pipe is 3.6 ft. The exit diameter of the pipe is 2.4 ft. The…

Q: A 13-cm diameter pipe of length 100 m with z = 60 m and f = 0.02. What is the flow rate? D=13cm,…

Q: of the pipes are listed as follows: Pipe A Length (m) Friction Coefficient, f Diameter (cm) 30 0.020…

Q: 0.5 m B 30 mm 5 m 8 m/s 50 mm 3 m mm

A: Given Data: Water flows into the Tee at 8 m/sec. It flows under a pressure of 40 kPa. Velocity of…

Q: 1: Water (assumed inviscid and incompressible) flows steadily in the vertical variable-area pipe…

Q: m³ 3 S Water flows at a rate of 0.035 in a horizontal pipe whose diameter is reduced from 15cm to…

Q: 2. Water (µ = 1.138x10³ kg/m-s) is flowing steadily in a 30m long and 4cm diameter horizontal pipe…

Q: PROBLEM 5 A 4-in.-diameter pipe carries 300 gal/min of water at a pressure of 20 psi. Determine (a)…

Q: In the figure, ideal fluid (water) flow from the infinity large basin through the atmosphere.…

A: Given:- absolute vapour pressure=0.025 kgf/cm2 absolute atmospheric pressure = 1kgf/cm2 AB dia=0.30m…

Q: 3. Determine the Velocity and discharge through the 150mm diameter pipe shown a) assuming no head…

Q: Given the following data for three pipes in parallel: Pipe 1: D1 = 450 mm, L1 = 800 m ; Pipe 2: D2 =…

A: Given: Three pipes in parallel Length of pipes Diameter of pipes Total discharge Friction factor…

Q: Water flows through a large size pipe with total and static pressure head of 0.5m and 0.3m of fluid.…

Q: Water flows at a rate of 17.0 e/s along a 100 mm diameter pipe AB, which branches at B into three…

A: GIVEN:Discharge =17.0 litre/sec Dia of AB=100mm…

Q: What is the flow rate m3/s inside the pipe if the diameter D=10 cm?

A: Given data : Head (h)=20 mmSpecific gravity (S)=13.6Diameter (d)=10 cm

Q: Water (assumed inviscid and incompressible) flows steadily in the vertical variable-area pipe shown…

A: Given:- pressure = 50kPa To find:- flowrate

Q: Pipe B 266 m, 160-mm diameter Pipe A 300 m, 200-mm diameter Pipe D S10 m, 250-mm diameter Pipe C 190…

Q: Water flows through a given pipe network. For said pipe network, a pipe 977m long branches out into…

Q: A steel pipe has an inside diameter of 25mm, is 20 meter long, carries 10degree water at the rate of…

A: what is the static pressure of the water at the outlet,P2=?

Q: Determine the velocity and pressure at sections 2 and 3 if water flows steadily through the pipe…

A: Use continuity equationA1v1=A2v2π4162×5=π482×v2v2=20ftsecApply Bernoullis theorem betweeen 1 and…

Q: 2) In the figure below, discharge rate at point A is 20 cfs of water. Find the head loss from A to…

Q: The velocity profile for the steady laminar flow of water through a 0.4-m-diameter pipe is defined…

A: IT IS GIVEN THAT -

Q: 2. A pipe carries water at a flow rate of 90 L/s. Determine the minimum inside diameter so that the…

Q: Compute the friction factor for the smaller pipe when two smooth pipes are connected in series where…

Q: Q2. Determine the flow rates in the three Cast Iron pipes in the figure shown (Assume complete…

A: Assuming the friction factor of cast iron =0.013 (from Moody chart)Applying Bernoulli's equation at…

Q: A pump is discharging 12 lit/sec of water through 100mm diameter smooth steel pipe. When the pump is…

Q: 0.001kg 1. Water (µ = -)is flowing through a 3-mm diameter, 9-m long horizontal pipe steadily at…

Q: В a b. Figure X5.2.2 5.2.3 Refer to Fig. X5.2.2. Assume a = 1 m, b = 4 m, and the flow to be…

Q: A 3-ft-diameter welded steel pipe (f = 0.0135) is carrying 15 cfs of water at 60°F. At this…

Q: Water flows at a rate of 0.035 m3 /s in a horizontal pipe whose diameter is reduced from 15 cm to 8…

Q: Consider the pipe network shown. Water enters at 440li/sec at node A and goes out at a rate of…

A: Solution Darcy–Weisbach formula for Head loss, hf = KQ2 Where, K = 16 fL2gπ2D5 f = 0.02 At node A =…

Q: A pipe has a slope of 1 in 100 and its length is 300 meters. Its diameter is 0.6 meter at the lower…

A: P1=68.07kPa D1=0.6m D2=1.2m Q=5400 lit/sec

Q: Water flows through a given pipe network. For said pipe network, a pipe 977m long branches out into…

A: f = 0.02 Length of 3rd pipe (L) = 885m Diameter of 3rd pipe = 0.3m Pressure drop between A and B =…

Q: The flow rate for the pipe system is 0.050 m3/s with a total head loss of 12 m. Use C = 120 for all…

Q: 5. Determine the flow in each pipe in the 3 reservoirs shown. EL 80m EL. 50m 2000m-500mm f0 025 EL.…

A: Transient and boundary-dominated flows are the two types of flow in reservoirs. Transient flow…

Q: Q4: Determine the maximum height increase provided by a 7.46 KW pump with a 6-cm-diameter inlet and…

A: Step 1

Question

D, - 16 in
P= 25 psi
", = 5 ft/s
D, = 8 in
P2
I = ?
D, = 12 in
P3
20 ft
15 ft
10 ft
Datum

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Similar questions

HW A nigid slab weighing 6o0 Kw is Placed uron two bronze vads and one Steel Vod Cach of bo00 mm2 area at a temPerature of 15 Ĉ as shown, find the temPerature at which the stress in steel Vod will be Zero ? takei Cuefficient of exransion for Steel= 12Mm/m.č Coefficient of exransion for brónze = 18 Mm/m.c %3D Young's modulus for steel = 200 G la Young's modulus for bronze = 80 GPa 600 IW -bronze 25orpm 30mm steel
0/10 FIND DEFLECTION IN Aluminum. IF E st= .200000 MPa, Ealu.=70000 MPa 100 kN R ALU.=30 MM Aluminum Steel 0.4 mm 2 mm 0.5 mm 0.25 mm no one 1m_ RST = 20 MM
carculate the Youngs modulus for the material of the bar shown below, The bar has an initial length of 400 mm and is measured to extend by 0.22 mm under a tensile load of 75KN, When the force is released the bar returns to its original length. The bar has the rectangular cross-section shown below. (17p) 20 mm 75 kN 75 kN 25 mum 400 mm
5 V Pipe A B Ja 1 T A Length 200 400 400 500 DO B B ( (cm) 50 2 20 40 50 theB this hLA +h₂B +h₂D = h total L Solve for QB D Assume -> QA=QD - QD in QA = QB +Qc → Solve for QA in terms of QB ↑ f= 0.030 for all fipes • Negate hm terms of QB huB = h₂e →→ use Darcy - Weisbach to get пис V 48:15 오 Solve for Q₁, QA & QD 20m чт QB & Qc relationship HOQUE
1. The aluminum bar of cross-se ctional are a 0.6 in.2 carries the axial loads shown in the fig ure. Compute the total change in length, in inches, of the bar given that E = 10 x 106 psi. 6000 lb 4000 lb 7000 lb 5000 lb + 3 ft 5 ft to 4 ft Total change in length (in ches)
Q3) Calculate the stretch (elongation) in spring AC wwww kan = 0 NA m- 100 Kg
7 30 Enercise:- diameter of 12mm A cylindrical rod 100 mm long with is subjected to a 30000 N. Assuming that the tensile load of deformation is entirely elastic and allowable elevation in pligmeter is allowable reduction in dligmeter is 0.015mm. choose amory only meeting requirent U (Poiss ons vahu) 0.33 below Material Aluminium alloy Bronze Titanium allow manimum 0.3 mm while manimum E (GPa) 70 100 110 0.34 3
For the box beam shown in Fig. if the modulus of elasticity E = 200 GPa, the flexural stresses at support for point (a) is ..................... MPa * 120mm 16.2kN 16.2KkN —{ 10.2KN/m £ fj//’/ £ W @ Q| im 3m im = 30 mm thickness of walls cross section Your answer
€ = - 20 N/nn Compute the displacements of the plate wing single quad ekmeent a 2 m I(0,1) 4 (2, 1) 0.5 m Im 3(2,0.5) E = 3(10*) Pa V = 0.3 2 (0,0) thickness Im %3D
b. Calculate "P" in KN considering tension failure on net area Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
TNT a 8 95% D7:20 Q44 D137 PROBLEM SET NO. 1_STRESS ANALYSIS_SIMPLE STRESS.pdf 1. As shown below, two pneumatic cylinders are used to control the motion and displacement of the device arm ABC. Assuming that the control rods attached at A and D each have a 20-mm diameter and happen to be parallel in the positicn shown. Solve for the average normal stress in (a) member AE, [b) member DG if the applied load at point Cis 800 N. 150 mm G00 m
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa Aluminum L=2m A=500mm 2m 2m E-72Mра P=20KN