Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force of F = 24 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.006 m² and member BC has a cross-sectional area of 0.005 m². The distance between joints A and C is 8.7 m, and the distance between joints A and B is 10.0 m. Answer directly. 41 Fc

Determine the shearing stress acting at joint C with a pin diameter d of 46 mm if a vertical force of F = 24 kN is applied at joint B using the figure below. Member AB has a cross-sectional area of 0.006 m² and member BC has a cross-sectional area of 0.005 m². The distance between joints A and C is 8.7 m, and the distance between joints A and B is 10.0 m. Answer directly. 41 Fc

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The five-bolt connection shown must support an applied load of P = 370 kN. If the average shear stress in the bolts must be limited to 185 MPa, determine the minimum bolt diameter that may be used in the connection. P 24.3 mm O 18.5 mm O 22.6 mm 29.3 mm O 14.0 mm
Solve clearly and neatly
The bell-crank mechanism is in equilibrium for an applied load of F₁ = 18 kN applied at A. Assume a = 290mm, b = 170mm, c = 70mm, and 0 = 35°. Pin B is in a double-shear connection and has a diameter of 23 mm. The bell crank has a thickness of 37 mm. Determine (a) the shear stress in pin B. (b) the bearing stress in the bell crank at B. Support bracket Answers: Tpin 8 = i Bell crank i a B MPa MPa F₂
Answer p1 and Part 2: Determine the shear force acting at each of the following locations:(a) x = 11.0- ft (i.e., just to the left of point B)(b) x = 11.0+ ft (i.e., just to the right of point B)(c) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: a) V = ____ kips b) V = ____ kips c) V = ____ kips Part 3: Determine the bending moment acting at each of the following locations:(a) x = 11.0 ft (i.e., at point B)(b) x = 28.5 ftNote that x = 0 at support A. When entering your answers, use the bending-moment sign convention detailed in Section 7.2. Answers: a) M = ____ kips-ft b) M = ____ kips-ft Part 4: Use your shear-force and bending-moment diagrams to determine the maximum bending moment, Mmax, and its location, xmax. Use the bending-moment sign convention detailed in Section 7.2.Answers: Mmax = ____ kips-ft xmax = ____ ft
Determine the stress in the Aluminum rod (Psi) after the load 68 (kips) is applied. The light rigid bar ABCD is pinned at 8 and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free.
When a force P of 750 N is applied to the pedal shown in the figure, find the diameter (mm) of this pin so that the resulting shear stress on the pin at C is 40 MPa.
For the clevis connection shown, the shear stress in the 0.577-in.-diameter bolt must be limited to 22 ksi. Determine the maximum load P that may be applied to the connection.
For the frame shown, a 4226-N load is acting on member ABD at D. If the allowable material shear stress for is 42 MPa, determine the required diameter (rounded off to the nearest 2.5 mm) of the pins at C and D. Pin C and pin D are subjected to double shear and single shear, respectively. If the thickness of member BC is 12 mm and that of member DE is 16 mm, determine the maximum bearing stress at C.
Two 6061-T6 aluminum tubular rods AB and BC are welded at B and loaded as shown in the figure (P = 60kN). Determine the normal stress in each section and the displacement of point B. Does this seem like a considerable displacement to you?
NOTE: A=3, B=1, C=7, so for example the dimension 1BA = 113 mm and so on %3D Figure 1 shows a cross section view of a three-piece member that has been nailed at A and B. Knowing that the allowable shear force in each nail is 2A N, determine the allowable V if the spacing s between the nails is 1CA mm. V IBA TIA A -2C 2AB 3B 1BC All dimensions are in mm The shape is not drawn in scale Figure 1
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. The diameter of rod (1) is d₁ = 23 mm and the diameter of rod (2) is d2 = 34 mm. Determine the absolute value of the normal stress in rod (2). 80 KN d₁ 232 MPa 255 MPa 305 MPa O 160 MPa O 220 MPa 140 KN 140 KN B
The solid rod shown in the figure below has radius of 0.63 in. If it is subjected to the force of 765 Ib, determine the state of stress at point A using superposition. C 8 in. 10 in. 765 lb 15 in. B