1-71. The joint is fastened together using two bolts.Determine the required diameter of the bolts if the failureshear stress for the bolts is Tail 350 MPa. Use a factor ofsafety for shear of F.S. = 340 kN40 KN30 mm80 KN30 mm

Shear stress:- Stress induced when force is applied parallel to the surface. It is given that, force…

Answered: Determine the required diameter of the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What are the three assumptions made when determining the average normal stress in an axially loaded bar.
i need the answer quickly
Urgent do it asap i will rate
answer only 2 . Shearing stress in threads of the bolt
An extension spring made from A313 stainless steel has a mean coil diameter of 10.00 mm and spring wire diameter of 1.38 mm with 72 body coils. If the spring has full twisted loop ends (hook and body have the same diameter), determine the factor of safety for end hook bending under a 21.5 N service load. Round your answer to 3 decimal places.
Determine the material index for a lightweight, stiff axially loaded bar.
19. The Knuckle Joint is made from SAE 1020 Steel having an allowable tensile strength of 15,000 psi and an allowable shear strength of 7500 psi. The axial load is 1 ton (recall, 1 ton = 2205 lb). Yoke Pin Rod -A The dimensions are as follows: D-0.652 in d-0.652 in c = 0.66 in b = 0.33 in m = 1.306 in e = 0.505 in Determine: a) Tensile stress (psi) at section A-A b) Factor of safety for a) c) Shearing stress (psi) in the pin d) Factor of safety for b) e) Bearing stress (psi) between the pin and the rod f) Factor of safety for e) g) Bearing stress (psi) between the pin and the yoke h) Factor of safety for g) i) Tensile stress (psi) across the hole in the rod j) Factor of safety for i) k) Tensile stress (psi) across the hole in the yoke 1) Factor of safety for k)
Determine the F.B.D of figure 1
B. Punched Sanding Disks In the blanking operation (9 sanding disks) the force on the punch was found to be 89kN. Each sanding disk is 2mm thk and 9 are punched together, determine the shear stress exerted by the punch for one punching operation. All dimensions in mm.
Part A -80 mm- P 75 mm -40 mm 30 mm If the bolt head and the supporting bracket are made of the same material having a failure shear stress of Tfail = 150 MPa, determine the maximum allowable force P that can be applied to the bolt so that it does not pull through the support. Apply a factor of safety of F.S. = 2.5 against shear failure. Express your answer to three significant figures and include the appropriate units.
Determine the deformation of an Axially Load Member?
20. A pin is used to join the two members shown. If the allowable average shearing stress in the pin is 190 MPa, what is the minimum required diameter for the pin? a. 8mm b. 3/8 inch 25 kN 12 mm C. 10 mm d. 1/2 inch 7.5 mm 12 mm 7.5 mm 25 kN 18. The motion of the follower of a cam-follower system is governed by x = R(1+1/2 coscot). If R = 70 mm and (= 62.8 rad/min, determine the magnitude of the acceleration of the follower, in mm/s², when t = 0.8 s. a. 18 c. 22 d. 24 b. 20

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS