Two in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and twelve A490 bolts with threads excluded from the shear plane. These bolts are available in ½ in. diameter increments ( in., ½ in., % in., %4 in., etc.). What is the smallest bolt size that will support a load of 55 kips? [in.] Be sure to check all four failure modes.

Two in. thick A36 steel plates are joined with two % in. thick A36 steel splice plates and twelve A490 bolts with threads excluded from the shear plane. These bolts are available in ½ in. diameter increments ( in., ½ in., % in., %4 in., etc.). What is the smallest bolt size that will support a load of 55 kips? [in.] Be sure to check all four failure modes.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter6: Fasteners

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Similar questions

Which of the following is the permissible working stress in psi of UNC bolts that has a stress area of 0.4 sq. in if material used is carbon steel with C = 5000?
Lap Joint Questions The following questions all use this figure. Assume a bolt will be put in each hole. The plates are made of A992 high-strength, low alloy steel and are 9.00" wide by 0.375" thick. This bearing-type connection will use A325 bolts with thread in the shear plane (A325-N). Record forces in pounds (not kips). Answers starting with a 1 should use four significant figures, all other answers should use three significant figures. (However, exact answers will be accepted.) Question 9 ) Listen How many fasteners will be counted for calculating the area of the net section? Your Answer:
A. PROBLEM ON TOPIC "KEYS AND COUPLINGS": A coupling with material AISI C1045 as rolled transmits 65.5 HP at 1750 rpm. The material of the 1.75 inch shaft... is also AISI C1045 as rolled and the key is cold drawn AISI C1020. N= 2.5. Determine the following: 1. Size of bolt (dia.) if there are 6 bolts made of AISI C1045 as rolled at a bolt circle of 5 inches. Note: Select standard bolt diameter from AT14 of DOME by Faires (see Lecture on fasteners for this Table) Calculated Dia: Standard Size to use: 2. Required b and t if a flat or rectangular key is used: Answer: 3. Required length of key, if a flat or rectangular key is used: Note: Calculate for two type of stresses on key, then select your answer. Length Based on shear length Based on compression: Length to use: 4. Required bif a square key is used: Answer: 5. Required length of key, if a square key is used: Note: Calculate for two type of stresses on kev, then select your answer. Length Based on shear length Based on compression:…
O b. 2:1 Oc. 1:2 O d. T: 1 QUESTION 10 What is the maximum tensile load P that can be applied to the bolted joint if the bolt diameter is 20 mm and the shear strength of the bolt material is 120 MNm 2 ? Apply a 'safety factor' of 1.2 in your calculations. Note: Please read about 'safety factors' and how they are applied in calculations. O a. 26.4 Nm2 O b. 26.4 kN O c. 62.5 kN O d. 62.5 MNm2 QUESTION 11
Question 7 Listen A 3/8-inch diameter bolt is subjected to a 2,135-lb tensile load. The bolt passes through a very thick plate to restrain it. The bolt head is 1/4-inch thick. Compute the shearing stress in the bolt head. Your Answer:
Pre-tensioning of a bolted joint is used to (a) strain harden the bolt head (b) decrease stiffness of the bolted joint (c) increase stiffness of the bolted joint (d) prevent yielding of the thread root
Bolt material is 304 stainless steel. frame material is Aluminum. kindly assume all the other values and find the bolt size / diameter for bolt. write all formulas and explain the procedure. there are 2 bolts 1 on left and 1 on right.
Define the term wide-flange sections?
Question two a) For a bolted assembly with ten bolts, the stiffness of each bolt is a= 10 MN/ and the stiffness of the members is ku 26 MN/mm per bolt. The joint is subject to occasional disassembly for maintenance and should be preloaded accordingly. Assume the external load is equally distributed to all the bolts. IR has been determined to use M6 1 dass S8 bolts with rolled threads. (a) Determine the maximum external load Paa that can be applied to the entire joint without exceeding the proof strength of the boits. (b) Determine the maximum esternal load Pn that can be applied ta the entire joint without causing the members te come out of compression b) A holding fixture for a workpiece 37.5 mm thick at the clamp locations is being designed. The detailof ane of the clamps is shown in the figure (Problem 10-2). A spring is required to drive the clamp upward when removing the workpiece with a starting force of 65 N. The clamp screw has an M10 - 125 thread. Allowa diametral clearance of…
1/2-inch thick steel bar is welded to the vertical supportA) Calculate the allowable load if the electrode is E7018, the bar is 1015 cold drawn steel, the support is 1020 cold drawn steel.
Please select all standard 3V sheave sizes (pitch diameters) between 6.5 in. and 12 in.. 7.80 In. 7.95 in. 11.25 In. 10.55 in. 6.85 in. 6.50 In.
15 Bolts and nuts are used for joining process. Select one: True False