An extension spring made trom A313 st 10.00 mm and spring wire diameter of 1 full twisted loop ends (hook and body ha of safety for end hook bending under a: Round your answer to 3 decimal places.

Q: a) Calculate the Pitch diameter for the following thread. Given the measurement over the wires is…

A:

Q: In the crank-slider shown, OA = 5 cm, AB = 15 cm and the offset e = 7 cm. Find the value of angle a…

A:

Q: The shaft shown in the Figure is driven by 3 KW motor. It transmits the power through the sprocket…

A: In this problem, we have to draw the loading diagram of the given diagram.

Q: 12 Find the moment about point O for the given Figure.   a.

A: Option B is correct.

Q: Problem 6 You've been asked to design a stamping tool as shown. What are the internal forces at A…

A: FBD

Q: 04/ Determine suitable groove dimensions for a 0101-16 '0' ring to seal against a solid cylinder.

A: Given that ,  Determine suitable groove dimension for a 0101-16 'O' ring to steal against a solid…

Q: Engine piston weight 220 g. Machine speed 4700 rpm. What is the high acceleration of the piston when…

A: The weight of engine piston is given as, w=220 g. The machine speed of the engines is given as,…

Q: An 18 teeth sprocket driving with 98 teeth sprocket at a center distance of 34 pitches. Find the…

A: Approach to solving the question: Detailed explanation: Examples: Key references:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: How did you calculate the 233.33 on the second part for the height from the end of the rod DE to the…

A:

Q: The Mean diameter of coil is 70 mm, wire diam made the compression coil spring. Find the Solid…

A: Spring

Q: Draw a complete shearing force and a bending moment diagram. Show detailed calculations Use the last…

A: F=54 KNTo determine:Shear force diagramBending moment diagram

Q: If the hydraulic cylinder at H draws rod BC in by a distance d = 4.545 in, how far does the slider…

A:

Q: opic: torsion in circular shafts The hollow shaft used in the system has the following conditions:…

A:

Q: E 12.5 m C А 8 m 5 m

A:

Q: Through load analysis, force and moment diagram are obtained, as shown below. Diagram below shows…

A: The force that occurs between mating gears is normal to the surfaces in contact. The axial force Fa,…

Q: Cork k =.045 also all are 300 K values ... please resolve

A:

Q: Solve using characteristics of equations. 5. у" + 14y' + 49у 3D 0%;B у(-4) %3 -1; у'(-4) 3D 5

A:

Q: For a shaft diameter of 7.50 inches, a rectangular key size of 2.0 in.(W) x 1.50 in. (H) should be…

A: As per the diagram and question given For a shaft diameter of 7.50 inches, a rectangular key size of…

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: The value of outer diameter of a muff will be .. mm, if the shaft diameter of a muff coupling, is…

A: Write the expression for the outer diameter of a muff. Here, d represents the shaft diameter.

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: If the torque and speed values are 125 N-m and 1800 revolution per minute, then the power required…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: intiguration. 250mm L₂= 164.35 mm O₂ = 86° 44=26mm L₁=173mm WAB-rad/s C 8₁= 90° B KAB=0.80672 rod/s²

A:

Q: A SHEROID HAS A FIRST ECCENTRICITY OF 0.81427. COMPUTE THE VALUE OF ITS FLATTENING.

A:

Q: 268 Threads M30 Ø25 032h6 0.8 Ø30 M20 18 rØ19.5 M24 40 НЕХ. 3 25 Ø15 10 12 M18 X 1.5 V 12 25 90…

A: 8. Length of the threads . 16. Threads

Q: 1. A bolt is expected to break at 105 ft-lb of torque. A cheater bar is being used to tighten the…

A: Given: The breaking torque is 105 lb-ft. Linear density of the cheater bar is 6.6 lb/ft. The bar is…

Q: Three blocks A, B, and C and a grooved block D have dimensions a, b, c, and d as follows: a =…

A:

Q: The steel shaft is formed by attaching a hollow shaft to a solid shaft. Determine the maximum torque…

A:

Q: 8 inch radius 8 inch circumference 8 inch all around 8 inch diameter R.70 4x 1.40 B IP 1.00 SECTION…

A: Select the correct statement about the notation circled in green and marked as letter.C. Assume all…

Q: f e (D d b C a k j a=38.0 b=41.5 c=39.3 d=40.1 e=55.8 f=39.4 q=36.7

A: a = 38.0b = 41.5c = 39.3d = 40.1e = 55.8f = 39.4g = 36.7h = 65.7i = 49.0j = 50.0k = 61.9l = 7.8m =…

Q: Find the pitch for an internal thread, if the depth of thread is 1 mm. Pitch (in mm) = %3D

A: Given: Depth of thread (d) = 1 mm To find: Pitch for an internal thread

Q: 2 Find T: For q=-KA when dr

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Laws of thermodynamics

Thermodynamics is a field of research, which needs the creation of absolute and ideal states and logical and practical examination of the actual conditions. By considering all the laws and theories of thermodynamics, the chemical reactions, the occurrence of processes, and physiological functions can be predicted with this field.