Determine the magnitude of the compression force the channel lock pliers exert on B. а 500 N с 321N 100 N b 653 N d 1.00 kN 250 mm- 50 mm MARE IN NAA 40° 100 N Determine the magnitude of the horizontal component of force pin A exerts on one of the pliers. а 383N с 321N b 0 d 283 N Determine the magnitude of the vertical component of force pin A exerts on one of the pliers. а 183 N с 221N b 283 N d 483 N

Determine the magnitude of the compression force the channel lock pliers exert on B. а 500 N с 321N 100 N b 653 N d 1.00 kN 250 mm- 50 mm MARE IN NAA 40° 100 N Determine the magnitude of the horizontal component of force pin A exerts on one of the pliers. а 383N с 321N b 0 d 283 N Determine the magnitude of the vertical component of force pin A exerts on one of the pliers. а 183 N с 221N b 283 N d 483 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SAQ 3 Determine the force-couple system acting at point 0. y 50 N 90 N C 40° B 40 N m 400 mm 1300 mm A 4 800 mm A 100 N 3 Answers: R = 83.4 N, 35° S of E, C = 87.4 N m, CW Ww 009 500 mm-
The two forces acting on the handles of the pipe wrenches constitute a couple 'M'. Express the couple as a vector Z 150 N 250 mm B 150 N OM -75i+22.5j N.m OM -75i+2.5j N.m OM -85i+22.5j N.m 150 mm 250 mm
150lv hinge P. R=4m Compuk the value af P such that zero, then the momet at A is draw N.F.D, S.F.D, d B.M.D.
60N LO 30 Nm, CCW 30 Nm, CW Q 270 Nm, CCW 270 Nm, CW LP L C. 1. Which of the following gives the moment of the 90.0 N-force about the center of the circular plate, 0? 44 510 N-M 2. Which of the following force and couple set acting at point O is equivalent to the given forces applied to the circular plate? 3. Which of the following single forces is equivalent to the given forces applied to the circular plate? A. B. B. 570 N-M 224 N 40° 231N 3m 150N 33.8⁰ 27.4° A P 90N LO D. А 44 1150 N-M 1150 N-M SON P 224 N 231N 33.8⁰ 27.4° P P A. LO 27.4⁰ 231 N C. 3m 33.80 231 N O O 2.28 m L D. L 56.20 224 N 33.8° 224 N A O 2.28 m 2.28 m
-100N/m |20N- h ਸਾਧ P E थे Zm B Am C med Im IR₁ R Draw the shear and moment diagram
Determine the moment at point B and point D of the beam 76416 Y B A */0in # -15in- C A 152916 D DOOD 1010-4
Determine al! fur ce mem bers of the truss Shown 4m 600 N
a) The components of the apparatus were assembled by the technician. b) Firstly, weigh the aluminium beam given on the measuring scale, with a span of 1000mm. c) Place both spring balances with Newton readings on the left and right end of the frame. 2 d) Zero the two spring balances. e) Load the beam on both spring balances, at Omm from the left end of the beam and at 1000mm on the right end of the beam ) With the use of two metal hangers, place the one metal hanger was at 200mm from the left-hand side of the beam and at 100mm from the right-hand side of the beam, thereafter both hangers will be loaded with loads/weights g) Load left hanger with 400g and right hanger with 500g h) Read and record the readings from both the spring balances as left and right reactions in newtons (N). RESULTS 400g 603.7g 500g 200mm 100mm 500mm 1000mm RL RR Figure 3. Experimental Force diagram of a simply supported beam.
ENGR 234: Statics 10-W: Simplification of Force-Moment Systems F4-19. Replace the loading system shown by a single resultant force acting at A and a single couple moment acting at A. State your answer as a resultant force magnitude and angle from the + x-axis, and as a moment magnitude with a CW/CCW designation. 900 N\30° 300 N 300N•M A 0.75 m 0.75 m 0.75 m 0.75 m Solution Strategy: 1. The planar nature of the problem lends itself to Scalar Analysis. 2. Resolve the 900 N force into its x- and y-components. 3. Using Scalar Analysis, compute the moments due to the forces: Use the Principle of Moments for the 900 force (i.e. use its components). The 300 N force already has an easily identifiable perpendicular distance to A. Keep track of the senses of these moments. 4. Determine the sense of the 300 N m couple, and then add this to the moments found in step 3 to find a single resultant moment at A. 5. Sum the forces in x and y and then combine them into a single resultant force in the…
Draw the FBD of member ABC 160 шн 90 mm 240 N 180 mm B 320 mm D. 125 mm 300 mm- Draw the FDBS of member ADB and BEC 1 m 1 m В 1 m D 1.6 m A
A aa 2/88 If the resultant of the forces shown passes through point A7 determine the magnitude of the unknown tension T which acts on the braked pulley. 1600 N Te sliz 275 N 0.5 1.8 m 1.5 m 300 N 1.25 m 50 0.6 m le T 3. To 650 N
Q2:-A rectangular gate AB in Fig is I m long and 1.5m wide into the paper, hinged at A. and resting on a smooth bottom at B. The Glycerin of sg- 0.89 acting on the left of gate, What the depth of water h will acting on gate? Water Glyceria 2 m Im 60