6. The steel gate 2.61m square of thickness 36.1mm is to be lifted by a frictionless pulley. The coefficient of friction between the dam and plate is 0.216 ,calculate the minimum force required to lift the gate if it is fully submerged to a depth of 1.61m. Use specific gravity of steel 8.0

Q: Problem 1 The gate shown is rectangular and has dimensions height h = 6 m by width b = 4 m. The…

A: Below is the clarified and detailed explanation for above tricky question.....if you are ok with my…

Q: 4. A vertical semi-circular gate with a diameter of 6 m is vertically submerged in water with its…

A:

Q: A hollow steel propeller shaft, 20 ft. long with 15 in outer diameter and 12 in. inner diameter,…

A:

Q: You are required to check the safety of the following beam: If the allowable shear stress of the…

A: Given data  Allowable shear stress = 8 MPa

Q: w = 300 KN Force on the gate, Fw=- CRR Calculate the force, S [kN] due to the stopper (shown) on the…

A:

Q: torque diagram,

A:

Q: a). What is the minimum diamétér of a solid 6m stéél shaft that will carry a shearing stress of not…

A:

Q: 0.9 m 0.9 m 1. For the force system shown, where F = 200 N and 0 = 30°. a) Determine the magnitude…

A:

Q: Answer must be:The maximum Torque T that can be applied is Tmax = 10.0139 kN•m

A: The objective of the question is to determine the maximum permissible torque T that can be applied…

Q: For equilibrium, compute the force in part B and its orientation for the given gusset plate. 8 kN…

A: The free body diagram of the given gusset plate is as follows:

Q: 1.) The cylindrical drum is filled with water with unit weight of water 9800 N/m3. The cylinder is…

A:

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

A:

Q: A stepped shaft ACB having solid circular cross sections with two different diameters is held…

A:

Q: Boom BC, as shown, supports a load of 15 kN which is then mainly supported by cable AB. The boom…

A: Data given:A = 1990 mm2x(bar) = 12.7mmIx = 6.29×106 mm4Iy = 0.358×106 mm4rx=56.4 mmry=13.4 mmloads =…

Q: Calculate the axial normal stresses in section 1 and 2. A (1) 30 kN (2) 10 kN = 20 mm d, = 15 mm %3D

A:

Q: For the thin-walled tubular section shown in the Figures that is applied a moment T = 4 kN * m,…

A: The strength of modern lightweight thin-walled structures is usually limited by the strength of…

Q: Sample Problems Talking: JOHN MAN SANTOS The gate shown submerged on water is hinged at B and rests…

A:

Q: 2) The simply supported beam with a channel cross-section carries the loads as shown. Determine the…

A:

Q: 10 kN A -20 kN/m 3 m 12 kN/m 3m B

A:

Q: 2 kN 2 m В 2 m 2 m 3 m 4 kN E O 8.94 kN (C) O 8.00 kN (T) O 8.94 kN (T) O NONE OF THE GIVEN CHOICES…

A:

Q: Q3/ For the beam and loading shown, determine the maximum normal stress due to bending. 150 kN 150…

A:

Q: 8 kN 4 kN ID B 3 m 3 m -3 m

A:

Q: a). What is the minimum diamétér of à sölid 6m stéél shaft that will carry a shearing stress of not…

A:

Q: The hemispherical dome in weighs 37.9 kN and is filled with water and attached to the floor by 7…

A:

Q: asap

A:

Q: 12.6 A link of a valve gear has to be curved in one plane, for the sake of clearance. Estimate the…

A: The given data is: F=2500 N The radius of the curve will be: R=(6.25+(5/2)) R=8.75 cm…

Q: What is the maximum Moment for the whole structure?

A:

Q: The screw eye below is subjected to two forces, F₁ = 78N and F₂ = 205N. Determine the magnitude and…

A: