60N LO 30 Nm, CCW 30 Nm, CW 270 Nm, CCW 270 Nm, CW L C. -10 1. Which of the following gives the moment of the 90.0 N-force about the center of the circular plate, O? 510 N-m 510 N-M 2. Which of the following force and couple set acting at point O is equivalent to the given forces applied to the circular plate? 3. Which of the following single forces is equivalent to the given forces applied to the circular plate? A A. B. A. 224N 40° 231N 3m 150N 33.8⁰ 27.4° A P P 90N L L 1150 N-M O 1150 N-M А SON P 224 N 231N 35.8° 27.4° P P 231 N C. 27.4 L 231 N 3m 2.28 m 224 N Lapt 33.g 224 N A 2.28 m 2.28 m

60N LO 30 Nm, CCW 30 Nm, CW 270 Nm, CCW 270 Nm, CW L C. -10 1. Which of the following gives the moment of the 90.0 N-force about the center of the circular plate, O? 510 N-m 510 N-M 2. Which of the following force and couple set acting at point O is equivalent to the given forces applied to the circular plate? 3. Which of the following single forces is equivalent to the given forces applied to the circular plate? A A. B. A. 224N 40° 231N 3m 150N 33.8⁰ 27.4° A P P 90N L L 1150 N-M O 1150 N-M А SON P 224 N 231N 35.8° 27.4° P P 231 N C. 27.4 L 231 N 3m 2.28 m 224 N Lapt 33.g 224 N A 2.28 m 2.28 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Resolve the 500N force into x- and y'-components
The given figure, (a) what is the reaction at C in kN? (b) what is the force at member AD and BD in kN?
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross sectional area of 500 mm^2. Link CD made of steel (E = 200 GPa) and has a cross sectional area of 600 mm^2. Determine the deflection at D in mm
Find a. Reaction at A in kN b. Deflection at B in mm c. Deflection at C in mm
The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and has a cross sectional area of 700 mm'; link CD is made of aluminum (E=70 GPa) and has a cross- sectional area of 500 mm. For the 28 kN force shown, deflection at E. A 0.4 m 0.3 m 28 kN B E 0.25 m 0.60 m
b) A cylindrical rod AB is made of aluminum is connected at B to a brass qylindrical rod BCD as shown in Figure 8. The shear modulus, G of aluminum rod AB is given by 27 GPa and the brass rod BCD of 39 GPa. The torsional reactions, TA and Ts are located at the ends of A and B, respectively. Given the portion CD of the brass rod is hollow and has an inner diameter of 40 mm, examine the angle of twist at A. 60 mm Tg = 1600 N - m 36 mm TA = 800 N m 250 mm 375 mm A 400 mm Figure 8
A set of forces acts on the assembly as shown. Note that the 120-N force is along the z-axis. 1.5 m Z 0.8 m 120 N X B 250 N 1. Which of the following statements is true regarding the assembly shown? None of the other statements is true. The moment of the 120-N force about the point A of the assembly is zero. The moment of the 120-N force about the x-axis is zero. The 250-N force does not produce moment about the y axis. N-m) of the forces ab
The beam shown below is suspended from two steelrods as shown and is initially horizontal. The midpointB of the beam is deflected 15 mm downward byforce Q. The steel used for the rods has properties E= 200 GPa and  = 275 MPa, determinea. the required maximum value of Q.b. the deformation of rod AD.c. the deformation of rod CE.
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
A bar AB of diameter 40 mm and 4 m long is rigidly fixed at its ends. A torque of 600 Nm is applied at a section of the bar, 1 m from end A. The fixing couples T and T at the supports A and B, respectively, are
Problem 4 In the structure shown below, each of the rods BD and CE is made of brass (E = 105 GPa) and has a cross- sectional area of 200 mm?. Determine the deflection of end A of the rigid member ABC caused by the 2-kN load. (Hint: 1) consider equilibrium using the free body diagram of the rigid member ABC, 2) consider compatibility between the deflections of points B and C, 3) consider force-deformation relation of rods BD and CE) DO E 2 kN 225 mm В F 550 mm 75 mm 100 mm
The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and has a cross sectionnal area of 700 mm; link CD is made of aluminum (E=70 GPa) and has a cross sectional area of 500 mm. For the 28 kN force shown, deflection at E. 0.4 m 0.3 m 28 kN B 0.25 m 0.60 m