Answered: Determine the difference of pressure…

Determine the difference of pressure between points A and B in kPa. a 2.2m 1.3m 3.2m d 1.2m e 2.2m Keroane .82 water water 18 Oil Mereary

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. You are traversing along a centerline, (S 45° 00' E), at Station 1+50, you establish a BC, for a curve with R = 400', Delta = 50°, which is concave to the north, and then transitions into a compound curve, also concave to the north, with R = 300', Delta = 40°, which sets an EC for this configuration. Determine the T1 and T2 from the attached Exhibit A sketch. Show your work on Exhibit A, show your answers here.
ASAP
Addition Work Assignment for Statics (CE.122) UGI-Semester 2 ملاحظات . تكون الإجابة بخط اليد حصرا ويتم كتابة الاسم الكامل والتوقيع على جميع أوراق الإجابة. تسلم الإجابة الى القسم عن طريق الطالب نفسه ولا يمكن ارسالها بيد طالب آخر. أي مساعدة خارجية من طالب اخر او شخص اخر يعتبر غش ويتم اتخاذ الإجراءات القانونية بشأنه. Q1: For the frame and loading shown, determine the components of the forces acting on member DABC at B and D. B 12kN 0.5m E F 6kN 0.5 m G H 0.6 m 0.4 m 0.2 m Q2: Determine the force in members DE, EI, GI and HI for the truss shown below. 4-6-6-4-4--6- 6+ 44 66 6-4 100 75 kN kN 75 kN 25 kN D 25 kN E 3 4 F B Κ H 14 G Dimensions in meters
طرقة ارتفاعالجهاز HI = B.M+Bs = R.L =HI - F(I.S) = Point B.S aiel's I.S F.S bot H.I R.L uio) REMARKS 1 B.M 1.315 16.815 15.5 2 A 1.49 3. 1.362 (TP.) 1571 1.3१2 5 DCT.P.) 1.601 1409 1.651 7 1.600 8 1.652 x عمل التد قيق لحا اتے
i need the answer quickly
None
Elementary beam theory predicts that the axial bending stress ox in a prismatic beam is given by: ox = (M.I,M,L)y+(M,I.-M.I.) (1,1₂-13/2) where My and M₂ are bending moments applied to a cross-section, and where ly, lz and lyz are second moments of area in the usual notation (Oxyz is a Cartesian coordinate system in which the x axis corresponds to the centroidal axis of the beam). (iii) A Z--section beam has the cross-section shown overleaf (see Figure QB2). The second moments of area of the section about the y and z axes are given as;; ly = 1.12x106mm² and I₂ = 2.87x106 mm4. Show that lyz = 1.35x106 mm² (use the parallel axis theorem). 100 60 10 y -10 10 60 Figure QB2 N (iv) Bending moments Mz = 2.0 kNm and My = 0 kNm act on a cross- -section of the beam of part (iii). Obtain an expression for the bending stress and sketch the orientation of the neutral axis with reference to the y and z axes. What is the maximum tensile value of the axial bending stress and where does it occur?
Local mean time of a place of longitude of 45°30' E is 8h 43m 14s AM. The corresponding Greenwich Mean Time (GMT) is (a) 5h 41m 14s PM (c) 11h 45m 14s AM (b) 11h 45m 14s PM (d) 5h 41m 14s AM
12 c.
Please show the process
Question 6. [3 Points] For a new project located in Trenton, NJ, it has been determined that the path fr the hydraulically most remote point of the drainage area to the point of concentration takes the followi path: 1. 800 ft of paved surface at a 1.5% slope 2. 140 ft of poor grass surface at a 0.9% slope 3. 60 ft of dense grass at a 6.0% slope 4. 1,600 ft of stream flow at a 1% slope. Calculate the total time of concentration using the following nomographs. 1000 -900 -800 -700 -600 -500 PAVED 400 لين ليسا ياليليليليليا 300 -200 BARE SOIL 100 90 80 70 60 50 40 82222222 -30 20 ויזיויויוייויייווווז LENGTH OF DRAINAGE STRIP IN FEET 10 POOR GRASS 0.5 1.0 CHARACTER OF GROUND AVERAGE GRASS DENSE GRASS OR WOODLAND PIVOT LINE PERCENT SLOPE OF GROUND דייוידי משר 2.0 235 3.0 000 5.0 10 120 35 30 25 20 S T T ° 6 0 INLET CONCENTRATION TIME IN MINUTES
762 Y 11:9 B/s ll bartleby.com تسجيل الدخول سؤال وجواب الة bartleby q لمة ...ربين 115 / مكتبة الأسئلة والأجوبة / هندسة مدنية / هندسة ...ب 12.5 م / ث. أحسب كفاءة التوربين 15 1 ابدأ تجربتك الآن! الأسبوع الأول 4.99 دولار بلق. فقط سؤال Q: 115 m turbine → V, In the above example problem, a hydroelectric turbine at the base of a dam is shown schematically. The height of the water above the turbine station given as 115 m. This turbine produces 4.6 MW of electricity, and you may assume the losses in the system to be equivalent to 10 m of head of water. The diameter of the pipe at the turbine exit is 0.75 m, and the velocity of water exiting from the pipe is 12.5 m/s. Calculate the efficiency of the turbine. العربية الإنجليزية N H •..