Design the middle concrete beam B1 shown below, the service live load of 2 kN/m² and the service dead load of 2 kN/m². Note that the section width (bw = 300 mm), and the total depth (h=500 mm), the slab load is 45.63 kN/m. Use f'c = 30 MPa, fy = 400 MPa. Columns dimensions are (300*300) mm. The beam doesn't carry any walls. 0.3m 0.3m 0.3m 4m 4m H+ 0.3m B₁ 6m 0.3m B₁ 6m 0.3m

Design the middle concrete beam B1 shown below, the service live load of 2 kN/m² and the service dead load of 2 kN/m². Note that the section width (bw = 300 mm), and the total depth (h=500 mm), the slab load is 45.63 kN/m. Use f'c = 30 MPa, fy = 400 MPa. Columns dimensions are (300*300) mm. The beam doesn't carry any walls. 0.3m 0.3m 0.3m 4m 4m H+ 0.3m B₁ 6m 0.3m B₁ 6m 0.3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

38 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the nominal moment capacity in kN∙m of the beam in positive bending. Write the answer in 2 decimal places only.
Design Slab DEGH of the floor system shown below. Dead load pressure including the slab's weight is estimated at 5.3 kPa while live load pressure is 2.4 kPa. Use fc' = 21 MPa and fy = 345 MPa. The supporting beam is 350 mm x 500 mm. Use 12mm diameter bars. 6m A B 6m C 2.6 m D 2.6 m 2.6 m J E H K LL F I L
32 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 280 MPa for 20-mm bars and fy = 230 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in positive bending with the given material strengths and the tensile strain is limited to 0.004 upon crushing of concrete. Write the answer in 5 decimal places only.
A rectangular beam of 230 mm width and effective depth mm diameter. The grade of concrete is M 20, grade of steel is Fe 500. Given that for M20 grade of concrete, the ultimate shear strength = 450 mm, is reinforced with 4 bars of 12 Tue = 0.36 N/mm2 for steel percentage of p D 0.25, and = 0.48 N/mm2 for steel percentage Tuc %3D p = 0.5. For a factored shear force of 45 kN, the diameter (mm) of Fe500 steel 2 legged stirrups to be used at spacing of 375 mm should be
A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with a 4-20mm diamter bars and at the top with 2-16 mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f'c = 32.09 MPa and steel yield strength fy=345 MPa for 20mm bars and fy=275 MPa for 16mm bars. Determine the maximum steel area for a tension-conctrolled singly reinforced condition in positive bending with the given material strength.
TRIBUTARY METHOD OF LOAD DISTRIBUTION (3) 2. Consider the floor plan shown in Figure. The floor is 100mm thick F-6 @ 6.67' = 40 %3D C4 I- reinforced concrete. Determine the B2 GI B3 following: (a) load that acts on floor beam B1, (b) load that acts on beam B5, (c) the load acting on corner column C1, and (d) the load acting on interior B4 2 @ 10' = 20' B) C2 I- B5 –I- I G4 G2 G3 B1 5 @ 8'= 40' column C2 ©-I- C3 Ci 40' 20 *Neglect the weight of joists
For the beam shown below, determine the steel area required for the section shown below. The cross-section dimensions are limited to the values shown. If compression steel is required, assume that it will be placed at a distance 70 mm from the compression face. Assume f'c = 28 MPa and Fy = 420 MPa. The concrete is normal weight. Assume: Mu = 1000 kN.m. b%3D 300 mт. d = 550 mm. T70 mm b mm mm
A rectangular reinforced concrete beam has a length of 14 m is simply supported atboth ends. The width of beam is 350mm and the overall depth is 550 mm. Determine the area of the steel reinforcements if the beam is to carry a DL = 15kN/m and LL =18kN/m. The concrete strength fc = 25 and steel yield fy = 400 ��. Use 60 mm concretecover.
Design the slab reinforcement if the maximum positive moment is Mup=wul2/11 . and the maximum negative moment is Mup=wul2/19. Include the design for S&T bar. Given: length = 6m span = 2m Wu= 8.572 kPa Slab thickness = 150 mm f'c = 28 MPa fy= 219 MPa main bar = 10 mm s&t bar = 8mm
A rectangular concrete beam has a width of 300mm and an effective depth of 550mm. The cantilever beam is loaded as shown. Assume f = 21 MPa and fy = 312 MPa. Compression reinforcement if necessary shall be placed at a depth 80mm from the outermost compression concrete. Determine the required number of 25mm tension bars. Draw the details of the rectangular beam. 20 kN/m 3 m 2 m 2 m 40 kN
Design the Beam AB Below by using Working Stress Method; A 4.3 kN/m 3.2 m Dead Load, D.L=7 kN/m Live Load, L.L = 4.3 kN/m The allowable compressive stress of the concrete, fc 13 N/mm² Allowable tensile stress in steel, fs = 160 N/mm2 Modulus of elasticity of steel, Es 210000 Mpa Modulus of elasticity of Concrete, Ec = 22000 Mpa Beam Width, b= 200 mm
34 A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with 4-20-mm-diameter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is 80 mm and at the bottom is 70 mm. Use concrete strength f’c = 21 MPa and steel yield strength fy = 350 MPa for 20-mm bars and fy = 275 MPa for 16-mm bars. Determine the maximum steel ratio if the beam is singly reinforced in negative bending with the given material strengths and the tensile strain is limited to 0.005 upon crushing of concrete. Write the answer in 5 decimal places only.