9:43 Assignment 3_ec751152d203b... Q. I Determine the moments at A, B, and C, then draw the moment diagram for the beam. The moment of inertia of each span is indicated. Assume support at B is a roller and A and C are fixed. E = 29(10³) ksi. A 1 k/ft 12 kN/m ||10A- -10 ft- LAB = 900 in A 800 lb/ft TARNEABLE I OB 24 ft Q. 2 Determine the member moments at B and C, then construct the shear and moment diagrams for the beam. All connections are pins. Assume the horizontal reactions are zero. El is constant. B w = 5 kN/m -10 ft- Q. 3 Determine all reactions and draw the shear and moment diagrams for the beam shown below. E is constant. 35 k B C BC= 1200 in -8 ft-8 ft- P = 40 kN 30 k -10 ft El= constant 1.21 12 m OD 12 kN/m Q. 4 Determine all reactions and draw the shear and moment diagrams for the beam shown below. El is constant. .... m Figure I 2 k/ft -20 ft- 59 2 Figure 2 Figure 3 Done E Figure 4 Page | 2

9:43 Assignment 3_ec751152d203b... Q. I Determine the moments at A, B, and C, then draw the moment diagram for the beam. The moment of inertia of each span is indicated. Assume support at B is a roller and A and C are fixed. E = 29(10³) ksi. A 1 k/ft 12 kN/m ||10A- -10 ft- LAB = 900 in A 800 lb/ft TARNEABLE I OB 24 ft Q. 2 Determine the member moments at B and C, then construct the shear and moment diagrams for the beam. All connections are pins. Assume the horizontal reactions are zero. El is constant. B w = 5 kN/m -10 ft- Q. 3 Determine all reactions and draw the shear and moment diagrams for the beam shown below. E is constant. 35 k B C BC= 1200 in -8 ft-8 ft- P = 40 kN 30 k -10 ft El= constant 1.21 12 m OD 12 kN/m Q. 4 Determine all reactions and draw the shear and moment diagrams for the beam shown below. El is constant. .... m Figure I 2 k/ft -20 ft- 59 2 Figure 2 Figure 3 Done E Figure 4 Page | 2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

265 Determine and locate the resultant of the two nt 0 forces. acting on the I-beamn. 3 m Problem 2/65
Q3. A beam is subjected to the variable loading shown. Calculate the support reactions at A and B. w 2400 N/m | w = wo-kx³ 6m 1200 N/m 111x B
Determine the moments at Band C, then draw the moment diagram for the beam. Assume the supports at Band Care rollers and A and Dare pins. EI is constant. Solve using three moment equations 24kN/m 24kN/m B IC A -4 m 6 m 4 m D
Qi. Determine the resultant moment +be fig. show n below: 200N 3 m 70
10 ft 10 ft Problem # 1 8 k· ft 10 ft Use the Virtual Work as the Deflection OCurves of Actual, Primary and Structure with Redundant Cy. displacement method. Determine the reactions at the supports if the support at C is forced upwards 0.15in. Take E = 29000ksi and l= 600 in^4. 8 kft 1oft Note: Use Cy as the Use Compatibility Equation: redundant reaction. (+ 1) 0.15 -Ac + Gfcc
Determine all reactions and bar forces produced by the applied load in the truss. Take the vertical reaction By as the redundant. AE is constant. D 30 kips 15 B 20 20'-
1.BEAM ABC is fixed at both ends (A&C) and hinge supported at B. AB=6m (3I) BC=5m (2I), the beam carries a uniform load of 8KN/m from A-B and concentrated load of 36KN 3m from C. Use moment distribution method (1cycle) Determine the moment at B 2.Determine the deflection at midspan of the structure
Determine the moments acting at the ends of each member. Assume the supports at A and D are fixed. The moment of inertia of each member is indicated in the figure. E = 29(10) ksi. Prob. 11-24 6k/ lac 1200 in 10 ft lo- 600 in 15 ft TA S00 in D 24 ft
Determine the internal moment at point C of the beam. Give your answer in N-m and to 3 significant digits. 400) N/m 200 N/m -3 m C 3 m B
A rectangular beam has the following properties: fc'=28MPa fy=270MPa b=300mm d=450mm As=4 of 36mm diameter bars Compute For: 1.) If the fc' is reduced by 50%, the difference in the magnitude of the ultimate moment capacity is Blank 1kN.m.
t6. Determine the reaction at the supports A and C, B. By using double integration method. El is constant. 130 Ib/ft B -6ft-
1.3-5 Segments AB and BCD of beam A BCD are pin connected at x = 3 m. The beam is supported by a pin support at A and roller supports at C and D; the roller at D is rotated by 30° from the x axis (see figure). A trapezoidal distributed load on BC varies in intensity from 74 N/m at B to 37 N/m at C. A con- centrated moment is applied at joint A, and a 180 N inclined load is applied at the mid-span of CD. (a) Find reactions at supports A, C, and D. (b) Find the resultant force in the pin connection at B. (c) Repeat parts (a) and (b) if a rotational spring (k, is removed. = 68 N m) is added at A and the roller at C 200 N·m at 1.5 m 1.5 m joint A 180 N 74 N/m 37 N/m 4 30° 3 m 3 m 3 m Part (c) Remove roller Pin connection at C in part (c)